Previous product
Back to products
Fluke SBP810 Fluke Smart Battery Pack for the 810
$512.00
Excluding GST 10%
Next product
Fluke 830/SHIMS Alignment Set
$2,344.00
Excluding GST 10%
Fluke 830/MAGNET Mounting Set
$2,242.00Excluding GST 10%
Available on backorder
Related products
Close
Fluke TL26A Test Lead Set
Product Features:
- U-shaped nose for blade-shaped terminals
- Notched jaw for gripping screw heads, bare wire or terminals
- Serrated teeth for gripping threaded or wire-wrapped terminals
- Cluster of sharp needles for piercing small gauge wires (#22-#28 AWG)
- Large piercing needle for penetrating larger gauge wires
Close
Fluke TP220 SureGrip Test Probes
Product Features:
- Designed for probing closely spaced or recessed terminals
- Hard stainless steel probe tips
- Flat blade design holds securely in blade type electrical wall sockets
- Safety rating(s): CAT IV 600V, CAT III 1000V, 10A
- UL listed
- Rubber overmolded surfaces and finger-hugging curves
- Sharp, 12 mm stainless tip provides reliable contact
- For use with Models TL222 and TL224
- 1 – SureGrip Industrial Test Probe (Red)
- 1 – SureGrip Industrial Test Probe (Black)
Close
Fluke TL71 Test Lead Set
Fluke TL71 Offers
Test leads are an integral part of the complete measurement system and extend the capabilities of your digital multimeter. The TL71 premium test lead set has one pair of red and black comfort grip probes with flexible silicone-insulated, right-angle test leads. With distinctive comfort grip probes, they are heat and cold resistant with safety ratings up to CAT III 1000 V.
Features
- One pair (red, black) comfort grip probes with silicone insulated, right-angle test leads
- Recommended for µV measurements
- CAT II 1000 V, 10 A rating
- CAT III 1000 V, CAT IV 600V only with protective cap
- One year warranty
Applications
- Test and measurement
- Oil and gas
- R&D
- Electronics design
- Electronics service
- Repair and maintenance
- Electrical
- Industrial
Close
Fluke AC220 Alligator Clips
Product Features:
- Rubber overmolded surfaces and finger-hugging curves for comfortable, reliable grip
- Small, insulated, nickel-plated jaws
- Blunt tip grabs round screw heads up to 9.5 mm
- Safety rating(s): CAT IV 600V, CAT III 1000V, 10A rating
- UL listed
- For use with Models TL222 and TL224
Close
Fluke AC89 Piercing Test Clip
Product Features:
- Single probe pierces 0.25 to 1.5 mm insulated wire
- Small pin allows self-healing of insulation
- Safety rating(s): CAT IV 600V, CAT III 1000V, 5A rating
- UL listed
Close
AC288 Terminal Block Probe with Retractable Probe Tip
Key features
- Retractable probe tip designed for increased safety, while providing flexibility to reach deep connection points
- Recommended for use with TL224, TL222 or TL221 Test Leads
- 11.5 cm (4.5 in) insulated, flexible shaft
- 1 mm diameter probe tip extends out to 8.4 mm (0.33 in) length
- Retractable probe tip is made with stainless steel
- Safety rated: IEC 61010-031 Ed.1.12008, CAT III 1000 V, CAT IV 600 V
- Operating temperature: -20 °C to 55 °C (-4 °F to 131 °F), 90% RH
- One-year warranty
Close
Fluke AC283 Pincer Clips
Features
- 1A rating
- Use for continuity testing on circuit board components
- 4.49in (11.4cm) flexible insulated shaft
- CAT IV 600V, CAT III 1000V safety rated
- UL listed
- 1-year warranty
Close
Fluke AC175 Alligator Clip Set
Product Features:
- Slide-on alligator clips
- Clip jaws provide 8 mm opening with flexible boots
- Compatible with 4 mm banana plugs and test leads
- Safety rating(s): CAT IV 600V, CAT III 1000V, 10A
- For use with Models TL71, TL75, TL175 and TP175
