Comparison block insert for the Fluke 9140-A-156 Dry Block Temperature Calibrator.
What’s included with the Fluke 3140-4
- Fluke 3140-4 Comparison Block Insert, 6 x 1/4″
Fluke 3140-4 Comparison Block Insert, 6 x 1/4″
$512.00Excluding GST 10%
What’s included with the Fluke 3140-4
- Fluke 3140-4 Comparison Block Insert, 6 x 1/4″
Available on backorder
Related products
Close
Fluke 190 Series II 60MHz ScopeMeter Oscilloscope
Features
- Four independent isolated input channels
- 60, 100, 200 and 500 MHz bandwidths
- Sample rate: Up to 2.5 GS/s
- Sample rate resolution: Up to 400 ps
- Deep memory: 10,000 point per trace waveform capture
- CAT III 1000 V / CAT IV 600 V safety rating
- Seven hour, high performance Li-ion batteries
- Battery door for convenient battery access
- Isolated USB ports for memory devices and PC connectivity
Close
Fluke 1662 – Multifunction Electrical Tester
A solid, reliable, basic installation tester
- Tests voltage and frequency
- Checks wiring polarity to detect broken N wires
- Measures insulation resistance and loop and line resistance
- Measures motor windings with continuity test
- Calculates prospective earth fault current (PEFC/IK) and prospective short-circuit current (PSC/IK)
Close
Fluke BT-520 Battery Analyzer
Key features
Fluke BT510 key features:
- Battery Voltage – During the internal resistance test, Fluke Battery Analyzers also measure the voltage of the battery under test
- Discharge Volts – The Discharge mode collects the voltage of each battery multiple times at a user defined interval during a discharge or load test. Users can calculate the time a battery takes to drop to the cut-off voltage and use this time to determine the capacity loss of the battery
- Ripple Voltage Test – Measures unwanted residual ac component of the rectified voltage in dc charging and inverter circuits. Allows users to test ac components in dc charging circuits and find one of the root causes of battery deterioration
- Meter and Sequence Modes – The Meter mode is used for a quick test or troubleshooting. In this mode you can save and read the readings in a measurement or time sequence. The Sequence mode is for maintenance tasks with multiple power systems and battery strings. Before a task starts, users can configure a profile for the task for data management and report generation
- Threshold and Warning – Users can configure a maximum of 10 sets of thresholds and receive a Pass/ Warning/ Fail indication after each measurement
- Intercell Strap Resistance Test and Data Management – Measures the resistance of the intercell connection between batteries in a string. Once the measurements are completed Fluke Battery Management Software version 1.0.69 can now report the strap resistance for a battery string or historical data over time.
- AutoHold – When AutoHold is turned on, a reading is captured when it remains stable for 1 second. The reading is then released when a new measurement starts
- AutoSave – When AutoSave is turned on, measured values are saved to internal memory automatically after an AutoHold reading is captured
Close
Fluke 424D Laser Distance Meter
Professional-grade, automated endpiece correction, 80m/260ft range
Features
- Reduction of estimation errors
- Range: 80m/260ft
- Max range: 100m (330ft)
- Inclination sensor for taking measurements in hard to reach areas
- Compass provides a “heading” for distance measurement
- Automated endpiece correction
- Advanced laser technology for distance measurement
- Instant measurement with one-button operation
- Quick calculation of area (square footage) and volume
- Minimum/maximum function
- Improved battery life from automatic shut-off feature
- Enhanced Pythagoras calculation
- Tripod mode
- Stake out function
- Audible keypad feedback
- Storage of the last twenty measurements for quick recall of distance
- IP54 protection
Close
Fluke 1550C Digital Insulation Resistance Tester with IR3000 FC, 5kV
Features Fluke 1550C
- Quickly configure, start, and stop tests remotely, a safe distance away from any operating, energized equipment, using Fluke Connect® and a smartphone
- Real time trending gives you easy-to-see visual cues, rather than hard to read, rapidly changing values
- Automatic calculation of Dielectric Absorption (DAR) and Polarization Index (PI) with no additional setup
- Guard system eliminates the effect of surface leakage current on high-resistance measurements
- Selectable test voltages in 50 V steps from 250 to 1000 V, and 100 V steps above 1000 V
- CAT III 1000 V, CAT IV 600 V safety rating
- Warning function alerts the user that line voltage is present and gives the voltage reading up to 600 V AC or DC for increased user safety
- Measurements can be stored in up to 99 memory locations, with each location assigned a unique, user defined, label for easy recall
- Long battery life gives the user over 750 tests between charges
- Large digital/analog LCD for easy viewing
- Capacitance and leakage current measurement
- Ramp function for breakdown testing
- Resistance measurements up to 2 TΩ
- Timer settings up to 99 minutes for timed tests
Features Fluke IR3000FC Connector
- Fits over the IR port of your existing Fluke Tools
- Upgradeable by USB
- Immediately enables you to graph, save and share the tool’s reading with your team from your smart phone
Close
Fluke 1663 Multifunction Installation Tester
Features
- 500V AC/DC voltage measurement TRMS
- 0.1V resolution & 3.3MΩ input impedance
- 660V RMS overload protection
- 20, 200, & 2000Ω auto-ranging continuity test
- 0.01, 0.1, & 1Ω resolution
- >4V open circuit voltage
- L-N, L-PE, N-PE inputs
- 50, 100, 250, 500, & 1000V insulation test voltages
- Test smooth DC sensitive RCDs (Type B/B+)
- 200 & 2000Ω earth resistance test
- 0.1 & 1Ω resolution
- 125Hz frequency & 25V output voltage
- On/Off switchable auto-start for RCD & Looptest
- Time & date (with optional FlukeView software)
- IP40 rated housing
- Complies with IEC/EN, UL, ANSI/ISA, & CAN/CSA
Close
Fluke 190 Series II 500MHz 2 Channel ScopeMeter Oscilloscope
Features
- Four independent isolated input channels
- 60, 100, 200 and 500 MHz bandwidths
- Sample rate: Up to 2.5 GS/s
- Sample rate resolution: Up to 400 ps
- Deep memory: 10,000 point per trace waveform capture
- CAT III 1000 V / CAT IV 600 V safety rating
- Seven hour, high performance Li-ion batteries
- Battery door for convenient battery access
- Isolated USB ports for memory devices and PC connectivity
Close
Fluke 190 Series II 500MHz 4 Channel ScopeMeter Oscilloscope
Features
- Four independent isolated input channels
- 60, 100, 200 and 500 MHz bandwidths
- Sample rate: Up to 2.5 GS/s
- Sample rate resolution: Up to 400 ps
- Deep memory: 10,000 point per trace waveform capture
- CAT III 1000 V / CAT IV 600 V safety rating
- Seven hour, high performance Li-ion batteries
- Battery door for convenient battery access
- Isolated USB ports for memory devices and PC connectivity
