Fluke 810SMM Sensor Magnetic Mount for the 810.
Previous product
Back to products
Fluke 810SC-20 Sensor Cable for the 810
$340.00
Excluding GST 10%
Next product
Fluke 810SMP Sensor Mounting Pads for the 810, 10-pack
$56.00
Excluding GST 10%
Fluke 810SMM Sensor Magnetic Mount for the 810
$402.00Excluding GST 10%
Available on backorder
Related products
Close
Fluke AC283 Pincer Clips
Features
- 1A rating
- Use for continuity testing on circuit board components
- 4.49in (11.4cm) flexible insulated shaft
- CAT IV 600V, CAT III 1000V safety rated
- UL listed
- 1-year warranty
Close
Fluke TL26A Test Lead Set
Product Features:
- U-shaped nose for blade-shaped terminals
- Notched jaw for gripping screw heads, bare wire or terminals
- Serrated teeth for gripping threaded or wire-wrapped terminals
- Cluster of sharp needles for piercing small gauge wires (#22-#28 AWG)
- Large piercing needle for penetrating larger gauge wires
Close
Fluke AC89 Piercing Test Clip
Product Features:
- Single probe pierces 0.25 to 1.5 mm insulated wire
- Small pin allows self-healing of insulation
- Safety rating(s): CAT IV 600V, CAT III 1000V, 5A rating
- UL listed
Close
Fluke TL71 Test Lead Set
Fluke TL71 Offers
Test leads are an integral part of the complete measurement system and extend the capabilities of your digital multimeter. The TL71 premium test lead set has one pair of red and black comfort grip probes with flexible silicone-insulated, right-angle test leads. With distinctive comfort grip probes, they are heat and cold resistant with safety ratings up to CAT III 1000 V.
Features
- One pair (red, black) comfort grip probes with silicone insulated, right-angle test leads
- Recommended for µV measurements
- CAT II 1000 V, 10 A rating
- CAT III 1000 V, CAT IV 600V only with protective cap
- One year warranty
Applications
- Test and measurement
- Oil and gas
- R&D
- Electronics design
- Electronics service
- Repair and maintenance
- Electrical
- Industrial
Close
Fluke TP1 Slim Reach Test Probes
Features
- One pair (red, black) of slender probe bodies for probing closely spaced or recessed terminals
- Hard stainless steel probe tips
- Flat blade design to hold securely in blade type electrical wall sockets
- CAT II 1000V, 10 A rating
Close
Fluke H900 Test Lead Holder
Features
- Mounting holes for securing to wall or surface
- 10.98 x 3.5 x 1.26 inches (27.9 x 8.9 x 3.2 cm)
- 1-year warranty
Close
Fluke TL175 TwistGuard Test Leads
Features
- Extra-heavy duty strain relief on probe and plug
- Tested beyond 30,000 bends without failure
- -4 to 131°F (-20 to 55°C) operating temp
- Altitude of 6562ft (2000m)
- CAT II 1000V, CAT III 1000V, CAT IV 600V rated
- 10A max, Pollution Degree 2
- Conforms to EN61010-031
- 1-year warranty
Close
Fluke TL935 Patch Cords
Fluke TL935 Offers
- 3 sets (red and black pairs) of multi-stacking 4 mm banana plug patch cords
- Nickel-plated banana plugs
- 60 cm, 90 cm, 120 cm long PVC insulated leads
- 30 V rms or 60 V DC, 15 A
- One year warranty
- 1 – Patch Cord, 60 cm (Red)
- 1 – Patch Cord, 60 cm (Black)
- 1 – Patch Cord, 90 cm (Red)
- 1 – Patch Cord, 90 cm (Black)
- 1 – Patch Cord, 120 cm (Red)
- 1 – Patch Cord, 120 cm (Black)
