Fluke 810SMP Sensor Mounting Pads for the 810, 10-pack.
Previous product
Back to products
Fluke 810SMM Sensor Magnetic Mount for the 810
$402.00
Excluding GST 10%
Next product
Fluke 810T Non-Contact Precision Laser Tachometer for the 810
$252.00
Excluding GST 10%
Fluke 810SMP Sensor Mounting Pads for the 810, 10-pack
$56.00Excluding GST 10%
Available on backorder
Related products
Close
Fluke AC89 Piercing Test Clip
Product Features:
- Single probe pierces 0.25 to 1.5 mm insulated wire
- Small pin allows self-healing of insulation
- Safety rating(s): CAT IV 600V, CAT III 1000V, 5A rating
- UL listed
Close
Fluke TL910 Electronic Test Probes
Product Features:
- 1 mm tips access hard to reach test points
- Probe tip length up to 100 mm
- Test lead length: 1 m
- 3 sets of spring loaded gold tips
- 2 sets of stainless steel tips
- Safety rating(s): CAT II 1000V, 3A
Close
AC288 Terminal Block Probe with Retractable Probe Tip
Key features
- Retractable probe tip designed for increased safety, while providing flexibility to reach deep connection points
- Recommended for use with TL224, TL222 or TL221 Test Leads
- 11.5 cm (4.5 in) insulated, flexible shaft
- 1 mm diameter probe tip extends out to 8.4 mm (0.33 in) length
- Retractable probe tip is made with stainless steel
- Safety rated: IEC 61010-031 Ed.1.12008, CAT III 1000 V, CAT IV 600 V
- Operating temperature: -20 °C to 55 °C (-4 °F to 131 °F), 90% RH
- One-year warranty
Close
Fluke TP175 TwistGuard™ Test Probes 2mm Diameter Probe Tips
Key features
- Patented TwistGuard™ extendable tip shroud meets the highest electrical safety requirements to reduce tip exposure while providing the versatility needed for most measurements
- Ratings: CAT II 1000 V, CAT III 1000 V, CAT IV 600 V, 10 A max., Pollution Degree 2
Close
Fluke AC87 Heavy Duty Bus Bar Clips
Product Features:
- Flat, right angle design for connecting to bus bars
- Adjustable collar provides 2 ranges of jaw openings up to 30 mm
- Safety rating(s): CAT III 600V, 5A rating
- UL listed
|
Close
Fluke TL76 Test Lead Set
Features
- Removable, insulated IC caps allow probing on closely spaced leads and compliance with GS38
- CAT II 1000 V, 10 A rating
- CAT III 1000 V, CAT IV 600V only with protective cap
Close
Fluke TL26A Test Lead Set
Product Features:
- U-shaped nose for blade-shaped terminals
- Notched jaw for gripping screw heads, bare wire or terminals
- Serrated teeth for gripping threaded or wire-wrapped terminals
- Cluster of sharp needles for piercing small gauge wires (#22-#28 AWG)
- Large piercing needle for penetrating larger gauge wires
Close
Fluke TL224 Test Leads
Product Features:
- Rubber overmolded surfaces and finger-hugging curves for comfortable, reliable grip
- Safety shrouded, standard diameter banana plugs
- Right angle connector on one end and straight connector on other end
- Reinforced strain relief
- 1.5 meter silicone-insulated wire resists heat and cold
- Safety rating(s): CAT IV 600V, CAT III 1000V, 10A
- UL listed
