Measure the speed of motors, conveyor belts, and other moving and rotational systems with this tachometer. Additionally, this instrument is specifically designed to use with the 810 vibration meter.
Previous product
Back to products
Fluke 810SMP Sensor Mounting Pads for the 810, 10-pack
$56.00
Excluding GST 10%
Next product
Fluke SBP810 Fluke Smart Battery Pack for the 810
$512.00
Excluding GST 10%
Fluke 810T Non-Contact Precision Laser Tachometer for the 810
$252.00Excluding GST 10%
Available on backorder
Related products
Close
Fluke TL222 Test Leads
Features
- Designed to improve steadiness in slippery hands
- Rubber overmolded surfaces and finger-hugging curves
- Reinforced strain relief
- CAT IV 600V & CAT III 1000V safety rating
- 10A rating
- UL listed
- 1-year warranty
Close
Fluke TP175 TwistGuard™ Test Probes 2mm Diameter Probe Tips
Key features
- Patented TwistGuard™ extendable tip shroud meets the highest electrical safety requirements to reduce tip exposure while providing the versatility needed for most measurements
- Ratings: CAT II 1000 V, CAT III 1000 V, CAT IV 600 V, 10 A max., Pollution Degree 2
Close
Fluke TL75 Hard Point Test Lead Set
Product Features:
- Comfort grip probes
- 48 in. PVC insulated test leads with right-angle shrouded banana plugs
- Recommended for general purpose measurements
- Safety rating(s): CAT II 1000V, 10A; CAT IV 600V, CAT III 1000V only with protective cap
- CSA listed
Close
Fluke TL76 Test Lead Set
Features
- Removable, insulated IC caps allow probing on closely spaced leads and compliance with GS38
- CAT II 1000 V, 10 A rating
- CAT III 1000 V, CAT IV 600V only with protective cap
Close
Fluke H900 Test Lead Holder
Features
- Mounting holes for securing to wall or surface
- 10.98 x 3.5 x 1.26 inches (27.9 x 8.9 x 3.2 cm)
- 1-year warranty
Close
Fluke TP165X Probe
Features
- Probe designed for 1500 and 1650 series
- Tip length up to 0.735in
- Tip diameter of 0.04in
- Slim probe with test button keeps your eyes on the panel while probing hard to reach points.
Close
Fluke TL71 Test Lead Set
Fluke TL71 Offers
Test leads are an integral part of the complete measurement system and extend the capabilities of your digital multimeter. The TL71 premium test lead set has one pair of red and black comfort grip probes with flexible silicone-insulated, right-angle test leads. With distinctive comfort grip probes, they are heat and cold resistant with safety ratings up to CAT III 1000 V.
Features
- One pair (red, black) comfort grip probes with silicone insulated, right-angle test leads
- Recommended for µV measurements
- CAT II 1000 V, 10 A rating
- CAT III 1000 V, CAT IV 600V only with protective cap
- One year warranty
Applications
- Test and measurement
- Oil and gas
- R&D
- Electronics design
- Electronics service
- Repair and maintenance
- Electrical
- Industrial
Close
Fluke TL26A Test Lead Set
Product Features:
- U-shaped nose for blade-shaped terminals
- Notched jaw for gripping screw heads, bare wire or terminals
- Serrated teeth for gripping threaded or wire-wrapped terminals
- Cluster of sharp needles for piercing small gauge wires (#22-#28 AWG)
- Large piercing needle for penetrating larger gauge wires
