For use with the 810 vibration tester.
Previous product
Back to products
Fluke 810T Non-Contact Precision Laser Tachometer for the 810
$252.00
Excluding GST 10%
Next product
Fluke 830/MAGNET Mounting Set
$2,242.00
Excluding GST 10%
Fluke SBP810 Fluke Smart Battery Pack for the 810
$512.00Excluding GST 10%
Available on backorder
Related products
Close
Fluke TP220 SureGrip Test Probes
Product Features:
- Designed for probing closely spaced or recessed terminals
- Hard stainless steel probe tips
- Flat blade design holds securely in blade type electrical wall sockets
- Safety rating(s): CAT IV 600V, CAT III 1000V, 10A
- UL listed
- Rubber overmolded surfaces and finger-hugging curves
- Sharp, 12 mm stainless tip provides reliable contact
- For use with Models TL222 and TL224
- 1 – SureGrip Industrial Test Probe (Red)
- 1 – SureGrip Industrial Test Probe (Black)
Close
Fluke H900 Test Lead Holder
Features
- Mounting holes for securing to wall or surface
- 10.98 x 3.5 x 1.26 inches (27.9 x 8.9 x 3.2 cm)
- 1-year warranty
Close
Fluke AC283 Pincer Clips
Features
- 1A rating
- Use for continuity testing on circuit board components
- 4.49in (11.4cm) flexible insulated shaft
- CAT IV 600V, CAT III 1000V safety rated
- UL listed
- 1-year warranty
Close
AC288 Terminal Block Probe with Retractable Probe Tip
Key features
- Retractable probe tip designed for increased safety, while providing flexibility to reach deep connection points
- Recommended for use with TL224, TL222 or TL221 Test Leads
- 11.5 cm (4.5 in) insulated, flexible shaft
- 1 mm diameter probe tip extends out to 8.4 mm (0.33 in) length
- Retractable probe tip is made with stainless steel
- Safety rated: IEC 61010-031 Ed.1.12008, CAT III 1000 V, CAT IV 600 V
- Operating temperature: -20 °C to 55 °C (-4 °F to 131 °F), 90% RH
- One-year warranty
Close
Fluke TL71 Test Lead Set
Fluke TL71 Offers
Test leads are an integral part of the complete measurement system and extend the capabilities of your digital multimeter. The TL71 premium test lead set has one pair of red and black comfort grip probes with flexible silicone-insulated, right-angle test leads. With distinctive comfort grip probes, they are heat and cold resistant with safety ratings up to CAT III 1000 V.
Features
- One pair (red, black) comfort grip probes with silicone insulated, right-angle test leads
- Recommended for µV measurements
- CAT II 1000 V, 10 A rating
- CAT III 1000 V, CAT IV 600V only with protective cap
- One year warranty
Applications
- Test and measurement
- Oil and gas
- R&D
- Electronics design
- Electronics service
- Repair and maintenance
- Electrical
- Industrial
Close
Fluke AC89 Piercing Test Clip
Product Features:
- Single probe pierces 0.25 to 1.5 mm insulated wire
- Small pin allows self-healing of insulation
- Safety rating(s): CAT IV 600V, CAT III 1000V, 5A rating
- UL listed
Close
Fluke TP175 TwistGuard™ Test Probes 2mm Diameter Probe Tips
Key features
- Patented TwistGuard™ extendable tip shroud meets the highest electrical safety requirements to reduce tip exposure while providing the versatility needed for most measurements
- Ratings: CAT II 1000 V, CAT III 1000 V, CAT IV 600 V, 10 A max., Pollution Degree 2
Close
Fluke TL175 TwistGuard Test Leads
Features
- Extra-heavy duty strain relief on probe and plug
- Tested beyond 30,000 bends without failure
- -4 to 131°F (-20 to 55°C) operating temp
- Altitude of 6562ft (2000m)
- CAT II 1000V, CAT III 1000V, CAT IV 600V rated
- 10A max, Pollution Degree 2
- Conforms to EN61010-031
- 1-year warranty
