Line Cord with Angled Bed of Nails Clips for TS22 and TS22A Test
- Field replaceable line cord for the TS22 and TS22A models
- Braided line cord for additional strength
- Red and Black insulating boots
Previous product
Back to products
P3218RJ9 - Fluke Networks Line Cord with Angled Bed-of-Nails, Piercing Pin Clips and RJ-11 Plug
$213.00
Excluding GST 10%
Next product
P3218028 - Fluke Networks Line Cord with Angled Piercing Pin Clips
$198.00
Excluding GST 10%
P3218234 – Fluke Networks Line Cord with Angled Bed of Nails Clips
$213.00Excluding GST 10%
- Line Cord with Angled Bed of Nails Clips
- Field replaceable line cord for the TS22 and TS22A models
- Braided line cord for additional strength
- Red and Black insulating boots
Available on backorder
Related products
Close
FTK2000 – Simplifiber PRO Basic Singlemode Verification Kit
Product Highlights
Simple-to-use fiber-loss tester with advanced time-saving features. Choose from various kits with configurations to meet your fiber verification, inspection, and cleaning needs.
- Single-port, simultaneous dual-wavelength feature completes testing in half the time and saves measurements from both wavelengths into one record
- Additional wavelengths of 1490 and 1625 nm
- CheckActive™ feature emits an audible tone and displays an icon when a live fiber is detected, eliminating the need to set up a measurement
- FindFiber™ Remote ID enables one individual to quickly identify cable connections or routings (especially useful at patch panels), eliminating the need for multiple technicians on opposite ends of a fiber link to match color combinations
Close
PRO3000F50-KIT – Fluke Networks 50HZ Filter & Tone Generator Kit
Product Highlights
Pro3000 Series Tone & Probe Kits tone and trace inactive wiring.
- Clear – Innovative filter technology blocks interference (“buzz”) that makes tracing difficult (“F” models only)
- Precise – SmartTone™ technology provides five distinct tones for exact pair identification
- Sends loud tone up to 10 miles (16 kilometers) on most cables
- Loud speaker on probe makes the tone easier to hear through drywall, wood, and other enclosures
- Angled bed-of-nails clips allow easy access to individual pairs
Fluke Networks PRO3000 Tone Generator and Probe Kit
Key features
- Send tone signal up to 10 miles (16 km) on most cables
- Analog tone generator with bed-of-nails clips, unfiltered probe
- SmartTone™ provides 5 distinct tones for exact pair identification
- Continuity testing and line polarity confirmation
- Ergonomic sleek design, 3.5 mm headphone jack
Close
LIQ-KIT – Fluke Networks LinkIQ Cable+Network Tester Kit
Key Features
Cable testing you trust. Network testing you need.
- Measure network capacity up to 10 Gig via frequency based measurements
- Troubleshoot active networks by providing connected switch information (Switch Name, Port Number, and VLAN info)
- Install and troubleshoot PoE devices via Switch Negotiation and PoE Load test
- Graphical wiremap and length test to identify common faults that occur with cabling installation
- Document work through LinkWare™ PC reporting
- Supports Industrial Ethernet (EtherNet/IP, PROFINET, EtherCAT, and others)
- Industrial Ethernet Kit supports Industrial Connectors (M8D, M12D, M12X)
Close
FINDFIBER-6 – Fluke Networks Six FindFiber Remote ID
Set of six FindFiber Remote ID sources.
Close
CIQ-KIT – Fluke Networks CableIQ™ Qualification Tester Kit
Key features
Copper qualification tester troubleshoots and qualifies Ethernet network cabling speed (10/100/1000/VoIP)
- Works on live networks to provide Ethernet switch detection and device configuration
- Measure network capacity (10 Meg, 100 Meg, 1 Gig) to determine support for VoIP, data and video
- Advanced troubleshooting diagnostics; insertion loss, cross talk, noise issues
- Core troubleshooting features; length, distance to fault, graphical wire mapping, opens, shorts, power over Ethernet (POE) detection
- Tests all copper cabling media: twisted-pair, coax, and audio
Close
DSX2-8000 AP – 2Ghz Fluke Networks Cable Analyzer
- DSX-8000 Cable Analyzer
- Accelerates every step of the copper certification process
- Versiv™ modular design supports copper certification, fiber optic loss, OTDR testing and fiber end-face inspection
- Unmatched speed for Cat 6A, 8, Class FA, I/II and all current standards
- ProjX™ system manages job requirements and progress from set-up to systems acceptance, making sure all tests are completed correctly
- Taptive™ user interface simplifies set-up, and eliminates errors
- Analyze test results and create professional test reports using LinkWare™ management software
- Graphically displays the source of failures including
Close
DSX2-5000 AP – Fluke Networks Copper Tester, DSX-5000
Product Highlights
Accelerates every step of the copper certification process
- Unmatched speed for Cat 6A, 8, Class FA, I/II and all current standards
- ProjX™ system manages job requirements and progress from set-up to systems acceptance, making sure all tests are completed correctly
- Taptive™ user interface simplifies set-up, and eliminates errors
- Analyze test results and create professional test reports using LinkWare™ management software
