This set of four replacement fuse is compatible with Amprobe 30XR-A digital multimeter.
Previous product
Back to products
Fluke Amprobe FP160 Fuse
$17.00
Excluding GST 10%
Next product
Fluke Amprobe FP520 Fuse
$21.00
Excluding GST 10%
Fluke Amprobe FP375 Fuse
$27.00Excluding GST 10%
What’s included with the Amprobe FP375
- Amprobe FP375 Replacement Fuse, 0.25A/600V, Pack of 4
Available on backorder
Related products
Close
Fluke Amprobe 15XP-B Digital Multimeter VolTect
- Features
- The 15XP-B is the right choice for electronics engineers, technicians and field service
- Autoranging display for faster measurements
- TTL logic test for digital circuits
- Integrated tilt stand for easy bench use
- Diode test for component level troubleshooting
- Data Hold freezes display to “hold” measurement reading
- 750 V AC / 1000 V DC—highest voltage rating in this size of meter
- Special 2000M Ω measurement range
- Battery Life: 200 hours typical with carbon-zinc
- Size: (H x W x D) 155 mm x 72 mm x 32 mm (6.1 x 2.83 x 1.26 IN)
- Safety: CAT II 1000V, CATIII 600V, CE, N10140
Close
Amprobe AC50A AC Leakage Clamp Meter
-
Product Features:
- AC current measurement to 60A
- Leakage current measurement with resolution of 0.01mA
- AC voltage to 400V
- Resistance measurement and continuity beeper
- Min/max control to see largest or smallest values in series of measurements
- Relative value measurement to determine differentials
- Data hold to freeze measurement value on display
- Digital display with analog bargraph
- Jaw opening: 30 mm (1.2 in)
- Auto-power off to save battery life
- Minimum resolution 0.01mA
Close
Amprobe ACD-53NAV CAT IV 1000 A AC True-rms Navigator Clamp Meter
- True RMS technology improves accuracy in noisy environments
- Measures AC/DC voltage to 1000 V, AC/DC current to 600 A, plus resistance, frequency, capacitance, power and power factor, total harmonics distortion (THD) and individual harmonics from 1 to 25
- Includes inrush current measurement and phase rotation indication for 3-phase motors
- Non-contact voltage detection enhances safety
- Low pass filter enables measuring voltage and frequency on variable frequency drives
- Continuity beeper quickly identifies shorts and opens
- Large backlit digital display with analog bar graph presents the full picture
- Min, max and smart data hold
- Peak hold identifies spikes and transients
- In-jaw flashlight automatically lights when jaws open to illuminate dark panels and junction boxes
- Auto power off conserves battery life
- Maximum jaw opening accommodates large conductors up to 1.45″ (37 mm)
- Rubber overmold body absorbs shocks—drop proof to 4 feet (1.2 m)
- CAT IV-rated AC/DC current clamp meter
Close
Fluke Amprobe ACDC-100 1000 A AC/DC Clamp Meter
- Large, easy to read LCD display
- Auto and manual ranging
- Relative zero mode
- Auto power off
- Data hold
- MAX capture function for inrush current measurements (30 mS response)
- Diode test
- Audible continuity
- Accommodates conductors up to 2.0″ (50 mm) in diameter
- “Third hand” – test probe holder
- Rubber over-molded case with built-in probes storage
Close
Amprobe ALC-110 Leakage Current Clamp
-
Product Features:
- Measures:
- Earth and differential leakage currents
- Leakage currents through the earth (PE) conductor
- Appliance current consumption without interruptions to the circuit
- Low influence of external low frequency magnetic fields: @ IN: 3.500 mA – 600.0 mA ≤ 30 A/m, operating class 2
- True-RMS measurements for accuracy when measuring complex, non-sinusoidal waveforms
- Mechanical jaw lock with 1.2 in. (30 mm) opening assures accuracy of low current measurements
- Highest resolution of 0.001 mA while measuring up to 60 A
- Broad frequency range 15 Hz to 1 kHz
- Selectable filters:
- Low Pass 50/60Hz filter to perform measurements on equipment driven by Variable Frequency Drives (VFDs) or affected by high frequency noise
- Appliance Filter to conduct leakage current measurements on appliances
- No filter
- Selectable limits: 0.25 mA, 0.5 mA, 3.5 mA, 10 mA, 12 mA
- Max readings and hold function
- High safety rating: CAT III 600 V
- Battery-saving design with an auto backlight off and auto power off
Applications
- Trace the source of earth leakage current
- Identify intermittent GFCI trips without switching equipment off
- Check a system for an electrical break of insulation where current is flowing to the ground
- Where industrial leakage current testing is required
- Measures:
Close
Fluke Amprobe AD40B Mini-Clamp Ammeter
-
Product Features:
- Low-cost, miniature digital ammeter
- 400 A AC range
- Maximum jaw opening: 25.4 mm
- 4000-count display with bargraph
- Autoranging
- Data hold
- Auto-off
- 3 3/4 digit LCD (max reading 3999);
- Overrange indication: “OL indicated
- Power supply: two (2) 1.5V AAA batteries
Close
Fluke Amprobe 35XP-A Digital Multimeter with Temperature
- Temperature measurement capability to 1000 °C/1832 °F (type-K thermocouple included)
- 600 V AC/600 V DC – highest voltage rating in this class of meter
- Capacitance for motor run/start test
- 0.1 μA resolution for flame sensor testing
- Frequency to 1 MHz
- Resistance to 40 MΩ
- Data hold freezes display
- Magne-Grip™ Holster
- VolTect™ non-contact voltage detector
- Low battery indication
Close
Fluke Amprobe 38XR-A TRMS Digital Multimeter with Temperature
- Backlight, True-rms with with optical PC interface
- Frequency to 10 MHz,capacitance to 400 uF, temperature to 2372 °F
- Bright blue backlight
- 10 Amps AC/DC, fully safety fused
- Continuity beeper
- Min/max, average, relative, peak, and data hold
- Auto power off to save battery life
- Separate door for easy battery and fuse access
- Magne-Grip™ Holster with magnetic hanging strap
- Autoranging; display: 4-3/4 digit LCD, 10,000 counts with 41-segment analog bar graph
- Display update rate: 2/sec, nominal
- Power battery: 9 V NEDA 1604, JIS 006P, IEC 6F22
- Operating temperature: 0 °C to 45 °C at < 70 % R.H
- Input lead warning
