Highly characterized silicon pressure sensor offers accurate pressure measurements with measuring range of 0 to 2 MPa (0 to 300 psi) gauge pressure and accuracy of 0.02% full scale.
Previous product
Back to products
Fluke PM200-G1.4M Pressure Measurement Module, 0 to 1.4 MPa (0 to 200 psi) gauge
$2,919.00
Excluding GST 10%
Next product
Fluke PM200-G3.5M Pressure Measurement Module, 0 to 3.5 MPa (0 to 500 psi) gauge
$3,497.00
Excluding GST 10%
Fluke PM200-G2M Pressure Measurement Module, 0 to 2 MPa (0 to 300 psi) gauge
$2,919.00Excluding GST 10%
What’s included with the Fluke PM200-G2M
- Fluke PM200-G2M Pressure Measurement Module, 0 to 2 MPa (0 to 300 psi) gauge
Available on backorder
Related products
Close
Fluke 810 Vibration Tester
Features
- Plain-text diagnosis of standard faults:
- Unbalance
- Looseness
- Misalignment
- Bearing failures
- Fault severity (slight, moderate, serious, extreme)
- 200 rpm to 12000 rpm machine rotational speed range
- 5 Hz to 20 kHz Usable frequency bandwidth
- 2.56 kHz to 51.2 kHz sampling rate
- Lithium-ion, 14.8 V, 2.55 Ah battery
- 1/4 VGA, 320 × 240 color display
- Auto ranging
Close
Fluke 190 Series II 200MHz 2 Channel ScopeMeter Oscilloscope
Features
- Four independent isolated input channels
- 60, 100, 200 and 500 MHz bandwidths
- Sample rate: Up to 2.5 GS/s
- Sample rate resolution: Up to 400 ps
- Deep memory: 10,000 point per trace waveform capture
- CAT III 1000 V / CAT IV 600 V safety rating
- Seven hour, high performance Li-ion batteries
- Battery door for convenient battery access
- Isolated USB ports for memory devices and PC connectivity
Close
Fluke 820-2 LED Stroboscope
Features
- 30 to 300,000 FPM (flashes per minute)
- 0.5 to 5000 Hz frequency range
- FPM or Hz frequency setting
- 0.02% accuracy
- Digital pulse width modulation
- Multi-line LCD display
- Operating temp: 32 to 113°F (0 to 45°C)
Close
Fluke 6500-2 Portable Appliance Tester
Key features
Fluke Simplifies Portable Appliance Testing
- Dedicated key for each test for ‘one-touch’ testing
- Pre-set pass/fail levels to save time
- Large backlit display for easy reading
- Single mains socket for appliance connection
- Separate IEC socket for easy mains/extension lead testing
- Detachable test leads for quick field replacement
- Integral carrying handle
- USB port for data transfer
Close
Fluke 124B ScopeMeter Oscilloscope
Features
- Dual-input digital oscilloscope and multimeter
- 20 or 40MHz bandwidth
- 5mV to 200V/div sensitivity
- VDC and true-rms VAC ranges from 500mV to 750V
- 5000 count full scale reading
- Up to 2200V peak (max, min, & peak-to-peak modes)
- 5% FS accuracy (min or max), 10% (peak-to-peak)
- 500 counts full scale reading
- Up to 70MHz frequency for 124B & 125B
- Up to 50MHz for 123B
- Measure resistance, continuity, diode, & capacitance
- CE & CSA approved, CAT IV 600V safety rated
Close
Fluke 190 Series II 500MHz 2 Channel ScopeMeter Oscilloscope
Features
- Four independent isolated input channels
- 60, 100, 200 and 500 MHz bandwidths
- Sample rate: Up to 2.5 GS/s
- Sample rate resolution: Up to 400 ps
- Deep memory: 10,000 point per trace waveform capture
- CAT III 1000 V / CAT IV 600 V safety rating
- Seven hour, high performance Li-ion batteries
- Battery door for convenient battery access
- Isolated USB ports for memory devices and PC connectivity
Close
Fluke BT-520 Battery Analyzer
Key features
Fluke BT510 key features:
- Battery Voltage – During the internal resistance test, Fluke Battery Analyzers also measure the voltage of the battery under test
- Discharge Volts – The Discharge mode collects the voltage of each battery multiple times at a user defined interval during a discharge or load test. Users can calculate the time a battery takes to drop to the cut-off voltage and use this time to determine the capacity loss of the battery
- Ripple Voltage Test – Measures unwanted residual ac component of the rectified voltage in dc charging and inverter circuits. Allows users to test ac components in dc charging circuits and find one of the root causes of battery deterioration
- Meter and Sequence Modes – The Meter mode is used for a quick test or troubleshooting. In this mode you can save and read the readings in a measurement or time sequence. The Sequence mode is for maintenance tasks with multiple power systems and battery strings. Before a task starts, users can configure a profile for the task for data management and report generation
- Threshold and Warning – Users can configure a maximum of 10 sets of thresholds and receive a Pass/ Warning/ Fail indication after each measurement
- Intercell Strap Resistance Test and Data Management – Measures the resistance of the intercell connection between batteries in a string. Once the measurements are completed Fluke Battery Management Software version 1.0.69 can now report the strap resistance for a battery string or historical data over time.
- AutoHold – When AutoHold is turned on, a reading is captured when it remains stable for 1 second. The reading is then released when a new measurement starts
- AutoSave – When AutoSave is turned on, measured values are saved to internal memory automatically after an AutoHold reading is captured
Close
Fluke DS701 Diagnostic Videoscope
Key features
- High definition probe with dual-view camera
- Processing speeds that render a smooth, clear, consistent image
- 7” LCD screen for easy viewing
- Macro to micro zoom function
- Adjustable lighting to capture the best image
- Up is Up® technology for an appropriate orientation, regardless of the probe location
