Previous product
Back to products
Fluke Amprobe AC68C TRMS 600 A Clamp Meter
$667.00
Excluding GST 10%
Next product
Fluke Amprobe ACD-10 PLUS 600A Clamp Multimeter
$343.00
Excluding GST 10%
Fluke Amprobe ACD-6 PRO Digital Clamp Meter 600 V AC/DC
$285.00Excluding GST 10%
-
Product Features:
- AC current to 1000A
- AC and DC voltage to 600V
- Resistance
- Continuity beeper
- Diode test
- Relative zero mode
- Auto and manual ranging
- Auto power off
- Data hold
- Large, easy to read LCD display
- Accommodates conductors up to 1.77″ (45mm) in diameter
Available on backorder
Related products
Close
Fluke Amprobe 37XR-A TRMS Digital Multimeter
- Backlight, True-rms with component and logic test
- Inductance to 40 H, frequency to 40 MHz, capacitance to 400 μF, logic to 20 MHz
- Input warning tone when test leads are in wrong jack
- 10 Amps AC/DC, fully safety fused
- Continuity beeper
- Min/max, average, relative, peak, and data hold
- Auto power off to save battery life
- Separate door for easy battery and fuse access
- Magne-Grip™ Holster with magnetic hanging strap
- Autoranging; display: 4-3/4 digit LCD, 10,000 counts with 41-segment analog bar graph
- Display Update Rate: 2/sec, nominal
- Power Battery: 9 V NEDA 1604, JIS 006P, IEC 6F22
- Operating temperature: 0 °C to 45 °C at < 70 % R.H
Close
Fluke Amprobe ACDC-54NAV 1000 A AC/DC Navigator Clamp Meter with Temperature
-
Product Features:
- True-RMS technology improves accuracy in noisy environments
- Measures AC and DC voltage to 1000V
- Measures AC and DC current to 1000A
- Resistance, frequency, and capacitance measurements
- Power and power factor, total harmonics distortion (THD) and individual harmonics from 1 to 25
- Measures temperature from -58 to 1832°F (-50 to 1000°C)
- Includes inrush current measurement and phase rotation indication for 3-phase motors
- Non-contact voltage detection enhances safety
- Low pass filter allows measurement of voltage and frequency for variable frequency drives
- Continuity beeper quickly identifies shorts and opens
- Large backlit digital display with analog bar graph presents full picture
- Min, max and smart data hold
- Peak hold identifies spikes and transients
- In-jaw flashlight automatically lights when jaws open, illuminating dark panels and junction boxes
- Auto power off conserves battery life
- Maximum jaw opening accommodates conductors up to 1.60″ (45mm)
- Rubber overmold body absorbs shocks: drop proof to 4 ft. (1.2m)
- Meets CAT IV 600V /CAT III 1000V safety standards
Close
Fluke Amprobe ACD-14 PLUS Dual Display Clamp Multimeter with Temperature
-
Product Features:
- Dual displays permit simultaneous reading of amps and volts
- Measurement ranges include:
- AC current to 600A
- AC and DC voltage to 600V
- Capacitance to 3000 µF
- Resistance to 40MΩ
- Frequency to 40kHz
- Measures temperature with included K-type thermocouple probe
- Includes micro amps measurement for testing flame sensors
- Diode test quickly finds voltage drops
- Continuity beeper detects opens and shorts
- Autoranging feature instantly selects correct range
- Hold and maximum reading functions
- Thin jaws make it easier to access conductors in tight spaces
- Accommodates conductors up to 25 mm (1.0″) in diameter
- Auto power off and low battery indication help extend battery life
- Rubber, over-molded case absorbs shock
Close
Amprobe ALC-110 Leakage Current Clamp
-
Product Features:
- Measures:
- Earth and differential leakage currents
- Leakage currents through the earth (PE) conductor
- Appliance current consumption without interruptions to the circuit
- Low influence of external low frequency magnetic fields: @ IN: 3.500 mA – 600.0 mA ≤ 30 A/m, operating class 2
- True-RMS measurements for accuracy when measuring complex, non-sinusoidal waveforms
- Mechanical jaw lock with 1.2 in. (30 mm) opening assures accuracy of low current measurements
- Highest resolution of 0.001 mA while measuring up to 60 A
- Broad frequency range 15 Hz to 1 kHz
- Selectable filters:
- Low Pass 50/60Hz filter to perform measurements on equipment driven by Variable Frequency Drives (VFDs) or affected by high frequency noise
- Appliance Filter to conduct leakage current measurements on appliances
- No filter
- Selectable limits: 0.25 mA, 0.5 mA, 3.5 mA, 10 mA, 12 mA
- Max readings and hold function
- High safety rating: CAT III 600 V
- Battery-saving design with an auto backlight off and auto power off
Applications
- Trace the source of earth leakage current
- Identify intermittent GFCI trips without switching equipment off
- Check a system for an electrical break of insulation where current is flowing to the ground
- Where industrial leakage current testing is required
- Measures:
Close
Fluke Amprobe ACDC-100 TRMS 1000 A AC/DC Clamp Meter
Product Features:
- Performs True-RMS measurements for accuracy
- Measures AC current to 800A and DC current to 1000A
- Measures AC and DC voltage to 600V
- Capacitance and resistance measurements
- Continuity beeper quickly identifies shorts and opens
- Relative zero mode displays difference between actual reading and stored reference value
- Data hold freezes reading on display for further analysis
- Diode test quickly finds voltage drops
- MAX capture function measures inrush current (30 mS response)
- Easy to read backlit digital display
- Auto power-off to conserve battery life
- Equipped with “third hand” test probe holder
- Rubber over-molded case absorbs shock and provides built-in probe storage
- Accommodates conductors up to 2.0″ (50mm) in diameter
- CAT III 600V rated
Close
Fluke Amprobe ACD-14 TRMS-PLUS Dual Display Digital Clamp Multimeter
-
Product Features:
- Dual displays allow for simultaneous reading of amperage and voltage
- True-RMS for precise measurement results
- Thin jaws facilitate access in tight measurement spaces
- AC current to 600A
- AC and DC voltage to 600V
- Resistance to 40MΩ
- Capacitance to 3000 µF
- Temperature measurement with K-type thermocouple probe
- Frequency measurement
- In rush current measurement
- Diode test and continuity buzzer
- Micro Amps measurement for testing flame sensors
- Hold and maximum reading functions
- Accommodates conductors up to 28 mm (1.1″) in diameter
- Auto ranging instantly selects correct range
- Auto power off and low battery indication
- Rubber over-molded case
Close
Fluke Amprobe ACDC-52NAV AC/DC CAT IV 600 A TRMS Navigator Clamp Meter
-
Product Features:
- True-RMStechnology improves accuracy in noisy environments
- Measures AC and DC voltage to 1000V
- Measures AC and DC current to 600A
- Resistance, frequency, and capacitance measurements
- Power and power factor, total harmonics distortion (THD) and individual harmonics from 1 to 25
- Includes inrush current measurement and phase rotation indication for 3-phase motors
- Non-contact voltage detection enhances safety
- Low pass filter enables measuring voltage and frequency for variable frequency drives
- Continuity beeper quickly identifies shorts and opens
- Large backlit digital display with analog bar graph presents full picture
- Min, max and smart data hold
- Peak hold identifies spikes and transients
- In-jaw flashlight automatically lights when jaws open, illuminating dark panels and junction boxes
- Auto power off conserves battery life
- Maximum jaw opening accommodates conductors up to 1.45″ (37mm)
- Rubber overmold body absorbs shocks: drop proof to 4 ft. (1.2m)
- Meets CAT IV 600V /CAT III 1000V safety standards
Close
Fluke Amprobe 33XR-A Digital Multimeter with Temperature
-
Product Features:
- Frequency To 40 MHz, Temperature To 1832 F, Capacitance To 4000 microF
- Input Warning Tone When Test Leads Are In Wrong Jack
- 1000V/750V DC/AC
- 10 Amps AC/DC. Fully Safety Fused
- Resistance To 4ohm
- Min/max, relative, peak and data hold
- Auto power off to save battery life
- Separate door for easy battery and fuse access
- Magne-Grip Holster with magnetic hanging strap
- Display: 3-3/4 digit LCD, 3999 counts with 41-segment analog bar graph
- Display update rate: 2/sec, nominal
- Analog bar graph
- Overrange indication
- Operating temperature: 0 °C to 45 °C at < 70 % R.H.
- Storage temperature: -20 °C to 60 °C,
- Input warning tone when test leads are in wrong jack
