Previous product
Back to products
Fluke Amprobe AM-570 Industrial Multimeter
$365.00
Excluding GST 10%
Next product
Amprobe AMB-45 Insulation Resistance Tester
$1,533.00
Excluding GST 10%
Fluke Amprobe AMB-25 Digital Insulation Resistance Tester
$671.00Excluding GST 10%
- Tests insulation of wires, cables, transformers and electrical motors
- Selectable test voltages 250 V, 500 V and 1000 V
- Programmable timer to perform the dielectric absorption ratio test
- Sensitive ohmmeter for checking resistance of motor windings
Available on backorder
Related products
Close
Fluke Amprobe 35XP-A Digital Multimeter with Temperature
- Temperature measurement capability to 1000 °C/1832 °F (type-K thermocouple included)
- 600 V AC/600 V DC – highest voltage rating in this class of meter
- Capacitance for motor run/start test
- 0.1 μA resolution for flame sensor testing
- Frequency to 1 MHz
- Resistance to 40 MΩ
- Data hold freezes display
- Magne-Grip™ Holster
- VolTect™ non-contact voltage detector
- Low battery indication
Close
Fluke Amprobe 34XR-A TRMS Digital Multimeter with Temperature
- Autoranging; display: 3-3/4 digit LCD, 3999 counts with 41-segment analog bar graph
- Display update rate: 2/sec, nominal
- Operating temperature: 0 °C to 45 °C at < 70 % R.H
- True-rms digital multimeter with temperature and backlight
- Overrange indication
- Auto power off to save battery life
- Min/max, data hold and range lock
- Separate door for easy battery and fuse access
- Magne-Grip™ Holster with magnetic hanging strap
Close
Amprobe ALC-110 Leakage Current Clamp
-
Product Features:
- Measures:
- Earth and differential leakage currents
- Leakage currents through the earth (PE) conductor
- Appliance current consumption without interruptions to the circuit
- Low influence of external low frequency magnetic fields: @ IN: 3.500 mA – 600.0 mA ≤ 30 A/m, operating class 2
- True-RMS measurements for accuracy when measuring complex, non-sinusoidal waveforms
- Mechanical jaw lock with 1.2 in. (30 mm) opening assures accuracy of low current measurements
- Highest resolution of 0.001 mA while measuring up to 60 A
- Broad frequency range 15 Hz to 1 kHz
- Selectable filters:
- Low Pass 50/60Hz filter to perform measurements on equipment driven by Variable Frequency Drives (VFDs) or affected by high frequency noise
- Appliance Filter to conduct leakage current measurements on appliances
- No filter
- Selectable limits: 0.25 mA, 0.5 mA, 3.5 mA, 10 mA, 12 mA
- Max readings and hold function
- High safety rating: CAT III 600 V
- Battery-saving design with an auto backlight off and auto power off
Applications
- Trace the source of earth leakage current
- Identify intermittent GFCI trips without switching equipment off
- Check a system for an electrical break of insulation where current is flowing to the ground
- Where industrial leakage current testing is required
- Measures:
Close
Amprobe AC50A AC Leakage Clamp Meter
-
Product Features:
- AC current measurement to 60A
- Leakage current measurement with resolution of 0.01mA
- AC voltage to 400V
- Resistance measurement and continuity beeper
- Min/max control to see largest or smallest values in series of measurements
- Relative value measurement to determine differentials
- Data hold to freeze measurement value on display
- Digital display with analog bargraph
- Jaw opening: 30 mm (1.2 in)
- Auto-power off to save battery life
- Minimum resolution 0.01mA
Close
Fluke Amprobe ACDC-100 1000 A AC/DC Clamp Meter
- Large, easy to read LCD display
- Auto and manual ranging
- Relative zero mode
- Auto power off
- Data hold
- MAX capture function for inrush current measurements (30 mS response)
- Diode test
- Audible continuity
- Accommodates conductors up to 2.0″ (50 mm) in diameter
- “Third hand” – test probe holder
- Rubber over-molded case with built-in probes storage
Close
Amprobe ACD-10 TRMS-PLUS 600 A Clamp Multimeter
- AC/DC Voltage to 600 V
- AC Current to 600 A
- Thin jaws, only 0.4″ (10 mm) thick
- Resistance to 40 MΩ
- Continuity buzzer
- Capacitance to 3000 uF
- Frequency measurement
- In rush current
- Hold maximum reading functions
- Accommodates conductors up to 1.02″ (26 mm) in diameter
- Auto ranging
- Auto power off
- Rubber over-molded case
- Overload protected
- True-rms measurement
Close
Fluke Amprobe ACDC-3400 IND AC/DC CAT IV TRMS Clamp Meter
- True-rms sensing increases measurement accuracy in noisy environments
- Measures AC/DC current up to 1000 A, AC voltage to 1000 V and DC voltage to 750 V, frequency, resistance, and capacitance and duty cycle
- Peak hold checks transients and motor start currents for spikes
- Relative zero displays the difference between the actual reading and a stored reference value and may be used with any function or range
- Audible continuity helps quickly identify opens and shorts
- Auto and manual ranging for measurement speed and flexibility
- Data hold holds the reading on the display for further analysis
- Diode test quickly finds voltage drops
- Accommodates conductors up to 2″ (51 mm) in diameter
- Safety rated to CAT IV 600 V and CAT III 1000 V
- Auto power off conserves battery life
- Backlight makes it easy to read even in dark conditions
Close
Fluke Amprobe ACDC-100 TRMS 1000 A AC/DC Clamp Meter
Product Features:
- Performs True-RMS measurements for accuracy
- Measures AC current to 800A and DC current to 1000A
- Measures AC and DC voltage to 600V
- Capacitance and resistance measurements
- Continuity beeper quickly identifies shorts and opens
- Relative zero mode displays difference between actual reading and stored reference value
- Data hold freezes reading on display for further analysis
- Diode test quickly finds voltage drops
- MAX capture function measures inrush current (30 mS response)
- Easy to read backlit digital display
- Auto power-off to conserve battery life
- Equipped with “third hand” test probe holder
- Rubber over-molded case absorbs shock and provides built-in probe storage
- Accommodates conductors up to 2.0″ (50mm) in diameter
- CAT III 600V rated
