Previous product
Back to products
Fluke Amprobe DC205C Deluxe Hard Shell Case
$122.00
Excluding GST 10%
Next product
Fluke Amprobe DL248D Test Leads
$190.00
Excluding GST 10%
Fluke Amprobe DGC-1000A Clamp Ground Resistance Tester
$4,801.00Excluding GST 10%
- Accurate ground resistance measurement from 0.025 to 1500 Ohms
- True-rms current measurement including leakage current
- Accurate readings regardless of power quality in less than 10 seconds
- Continuity beep if the resistance is lower than 40.00 Ohms
- Simple and easy to use, no test leads or auxiliary electrodes necessary
- Data logging capability – 116 records
- Individual data point recording
- User selectable high low ohm audible alarms
- Auto power off (can be disabled)
- Low battery indicator
- Large LCD display
Available on backorder
Related products
Close
Fluke Amprobe 35XP-A Digital Multimeter with Temperature
- Temperature measurement capability to 1000 °C/1832 °F (type-K thermocouple included)
- 600 V AC/600 V DC – highest voltage rating in this class of meter
- Capacitance for motor run/start test
- 0.1 μA resolution for flame sensor testing
- Frequency to 1 MHz
- Resistance to 40 MΩ
- Data hold freezes display
- Magne-Grip™ Holster
- VolTect™ non-contact voltage detector
- Low battery indication
Close
Fluke Amprobe 34XR-A TRMS Digital Multimeter with Temperature
- Autoranging; display: 3-3/4 digit LCD, 3999 counts with 41-segment analog bar graph
- Display update rate: 2/sec, nominal
- Operating temperature: 0 °C to 45 °C at < 70 % R.H
- True-rms digital multimeter with temperature and backlight
- Overrange indication
- Auto power off to save battery life
- Min/max, data hold and range lock
- Separate door for easy battery and fuse access
- Magne-Grip™ Holster with magnetic hanging strap
Close
Fluke Amprobe ACDC-3400 IND AC/DC CAT IV TRMS Clamp Meter
- True-rms sensing increases measurement accuracy in noisy environments
- Measures AC/DC current up to 1000 A, AC voltage to 1000 V and DC voltage to 750 V, frequency, resistance, and capacitance and duty cycle
- Peak hold checks transients and motor start currents for spikes
- Relative zero displays the difference between the actual reading and a stored reference value and may be used with any function or range
- Audible continuity helps quickly identify opens and shorts
- Auto and manual ranging for measurement speed and flexibility
- Data hold holds the reading on the display for further analysis
- Diode test quickly finds voltage drops
- Accommodates conductors up to 2″ (51 mm) in diameter
- Safety rated to CAT IV 600 V and CAT III 1000 V
- Auto power off conserves battery life
- Backlight makes it easy to read even in dark conditions
Close
Fluke Amprobe ACD-51NAV CAT IV 600 A TRMS Navigator Clamp Meter
-
Product Features:
- True-RMS technology improves accuracy in noisy environments
- Measures AC/DC voltage to 1000V and AC current to 600A
- Resistance, frequency, and capacitance measurements
- Measures power factor, total harmonics distortion (THD) and individual harmonics from 1 to 25
- Provides DC micro amps measurements to test flame sensors
- Includes inrush current measurement and phase rotation indication for 3-phase motors
- Measures temperature from -58 to 1832°F (-50 to 1000°C)
- Non-contact voltage detection enhances safety
- Low pass filter enables measuring voltage and frequency for variable frequency drives
- Continuity beeper quickly identifies shorts and opens
- Large backlit digital display with analog bar graph
- Min, max and smart data hold
- Peak hold identifies spikes and transients
- In-jaw flashlight automatically lights when jaws open, illuminating dark panels and junction boxes
- Auto power off conserves battery life
- Maximum jaw opening accommodates large conductors up to 1.45″ (37mm)
- Rubber overmold body absorbs shocks: drop proof to 4 ft. (1.2m)
- Safety rated to CAT IV
Close
Amprobe ALC-110 Leakage Current Clamp
-
Product Features:
- Measures:
- Earth and differential leakage currents
- Leakage currents through the earth (PE) conductor
- Appliance current consumption without interruptions to the circuit
- Low influence of external low frequency magnetic fields: @ IN: 3.500 mA – 600.0 mA ≤ 30 A/m, operating class 2
- True-RMS measurements for accuracy when measuring complex, non-sinusoidal waveforms
- Mechanical jaw lock with 1.2 in. (30 mm) opening assures accuracy of low current measurements
- Highest resolution of 0.001 mA while measuring up to 60 A
- Broad frequency range 15 Hz to 1 kHz
- Selectable filters:
- Low Pass 50/60Hz filter to perform measurements on equipment driven by Variable Frequency Drives (VFDs) or affected by high frequency noise
- Appliance Filter to conduct leakage current measurements on appliances
- No filter
- Selectable limits: 0.25 mA, 0.5 mA, 3.5 mA, 10 mA, 12 mA
- Max readings and hold function
- High safety rating: CAT III 600 V
- Battery-saving design with an auto backlight off and auto power off
Applications
- Trace the source of earth leakage current
- Identify intermittent GFCI trips without switching equipment off
- Check a system for an electrical break of insulation where current is flowing to the ground
- Where industrial leakage current testing is required
- Measures:
Close
Fluke Amprobe ACD-3300 IND CAT IV TRMS Clamp Meter with Temperature
-
Product Features:
- Performs true-RMS measurements
- Measures AC current up to 1000 AC A
- Measures voltage up to 750V AC and 1000V DC
- Includes frequency, resistance and capacitance and duty cycle functions
- Uses included thermocouple to measure temperature up to 1832°F (1000°C)
- Peak hold and data hold functions
- Audible continuity and diode test
- Auto and manual ranging
- Auto power off
- Large backlit LCD display with bar-graph
- Accommodates conductors up to 2 in. (51mm) in diameter
- Safety rated to CAT IV 600 V, CAT III 1000 V
Close
Fluke Amprobe ACDC-54NAV 1000 A AC/DC Navigator Clamp Meter with Temperature
-
Product Features:
- True-RMS technology improves accuracy in noisy environments
- Measures AC and DC voltage to 1000V
- Measures AC and DC current to 1000A
- Resistance, frequency, and capacitance measurements
- Power and power factor, total harmonics distortion (THD) and individual harmonics from 1 to 25
- Measures temperature from -58 to 1832°F (-50 to 1000°C)
- Includes inrush current measurement and phase rotation indication for 3-phase motors
- Non-contact voltage detection enhances safety
- Low pass filter allows measurement of voltage and frequency for variable frequency drives
- Continuity beeper quickly identifies shorts and opens
- Large backlit digital display with analog bar graph presents full picture
- Min, max and smart data hold
- Peak hold identifies spikes and transients
- In-jaw flashlight automatically lights when jaws open, illuminating dark panels and junction boxes
- Auto power off conserves battery life
- Maximum jaw opening accommodates conductors up to 1.60″ (45mm)
- Rubber overmold body absorbs shocks: drop proof to 4 ft. (1.2m)
- Meets CAT IV 600V /CAT III 1000V safety standards
Close
Fluke Amprobe ACD-23SW Swivel Clamp Meter
-
Product Features:
- Performs true-RMS measurement
- 180 degree rotating head for optimal display viewing
- Advanced VoltTect non-contact voltage detection
- Easy to use with slim jaw design and one hand operation
- Measures AC current up to 400A
- Measures AC and DC voltage up to 600V
- Resistance and capacitance measurement
- Audible continuity
- Temperature measurement with type-K thermocouple probe
- Auto and manual ranging respectively offer quick checks and precise measurements
- Accommodates conductors up to 1.18″ (30mm) in diameter
- Auto power off to extend battery life
- Includes data hold function
- Safety rated toCAT III 600 V
