PVC test lead set compatible with Amprobe AM-140-A digital multimeter and AMB-45 insulation resistance tester. Connects the tester to a device for testing.
Previous product
Back to products
Fluke Amprobe MT1-LEADS Test Lead
$156.00
Excluding GST 10%
Next product
Amprobe 4 Earth Roads With Leads
$548.00
Excluding GST 10%
Fluke Amprobe MTL-45 Test Leads Set
$88.00Excluding GST 10%
- MTL-45 Test Lead Set
- PVC test lead set connects a compatible electrical test meter to a device for testing
- Set includes two 48″ lead wires, two standard probe tips, and two alligator clips
- 3.26″ alligator clips have 1.30″ jaw opening and teeth that grip the conductor to provide a more secure, hands-free connection than probe tips
- Meets International Electrotechnical Commission (IEC) safety standard 61010 and is certified for category III installations up to 1,000V (alligator clips are certified for category III installations up to 600V)
Available on backorder
Related products
Close
Fluke Amprobe ACD-14 TRMS-PLUS Dual Display Digital Clamp Multimeter
-
Product Features:
- Dual displays allow for simultaneous reading of amperage and voltage
- True-RMS for precise measurement results
- Thin jaws facilitate access in tight measurement spaces
- AC current to 600A
- AC and DC voltage to 600V
- Resistance to 40MΩ
- Capacitance to 3000 µF
- Temperature measurement with K-type thermocouple probe
- Frequency measurement
- In rush current measurement
- Diode test and continuity buzzer
- Micro Amps measurement for testing flame sensors
- Hold and maximum reading functions
- Accommodates conductors up to 28 mm (1.1″) in diameter
- Auto ranging instantly selects correct range
- Auto power off and low battery indication
- Rubber over-molded case
Close
Amprobe ALC-110 Leakage Current Clamp
-
Product Features:
- Measures:
- Earth and differential leakage currents
- Leakage currents through the earth (PE) conductor
- Appliance current consumption without interruptions to the circuit
- Low influence of external low frequency magnetic fields: @ IN: 3.500 mA – 600.0 mA ≤ 30 A/m, operating class 2
- True-RMS measurements for accuracy when measuring complex, non-sinusoidal waveforms
- Mechanical jaw lock with 1.2 in. (30 mm) opening assures accuracy of low current measurements
- Highest resolution of 0.001 mA while measuring up to 60 A
- Broad frequency range 15 Hz to 1 kHz
- Selectable filters:
- Low Pass 50/60Hz filter to perform measurements on equipment driven by Variable Frequency Drives (VFDs) or affected by high frequency noise
- Appliance Filter to conduct leakage current measurements on appliances
- No filter
- Selectable limits: 0.25 mA, 0.5 mA, 3.5 mA, 10 mA, 12 mA
- Max readings and hold function
- High safety rating: CAT III 600 V
- Battery-saving design with an auto backlight off and auto power off
Applications
- Trace the source of earth leakage current
- Identify intermittent GFCI trips without switching equipment off
- Check a system for an electrical break of insulation where current is flowing to the ground
- Where industrial leakage current testing is required
- Measures:
Close
Fluke Amprobe 37XR-A TRMS Digital Multimeter
- Backlight, True-rms with component and logic test
- Inductance to 40 H, frequency to 40 MHz, capacitance to 400 μF, logic to 20 MHz
- Input warning tone when test leads are in wrong jack
- 10 Amps AC/DC, fully safety fused
- Continuity beeper
- Min/max, average, relative, peak, and data hold
- Auto power off to save battery life
- Separate door for easy battery and fuse access
- Magne-Grip™ Holster with magnetic hanging strap
- Autoranging; display: 4-3/4 digit LCD, 10,000 counts with 41-segment analog bar graph
- Display Update Rate: 2/sec, nominal
- Power Battery: 9 V NEDA 1604, JIS 006P, IEC 6F22
- Operating temperature: 0 °C to 45 °C at < 70 % R.H
Close
Fluke Amprobe 35XP-A Digital Multimeter with Temperature
- Temperature measurement capability to 1000 °C/1832 °F (type-K thermocouple included)
- 600 V AC/600 V DC – highest voltage rating in this class of meter
- Capacitance for motor run/start test
- 0.1 μA resolution for flame sensor testing
- Frequency to 1 MHz
- Resistance to 40 MΩ
- Data hold freezes display
- Magne-Grip™ Holster
- VolTect™ non-contact voltage detector
- Low battery indication
Close
Fluke Amprobe ACD-6 PRO Digital Clamp Meter 600 V AC/DC
-
Product Features:
- AC current to 1000A
- AC and DC voltage to 600V
- Resistance
- Continuity beeper
- Diode test
- Relative zero mode
- Auto and manual ranging
- Auto power off
- Data hold
- Large, easy to read LCD display
- Accommodates conductors up to 1.77″ (45mm) in diameter
Close
Fluke Amprobe ACDC-100 1000 A AC/DC Clamp Meter
- Large, easy to read LCD display
- Auto and manual ranging
- Relative zero mode
- Auto power off
- Data hold
- MAX capture function for inrush current measurements (30 mS response)
- Diode test
- Audible continuity
- Accommodates conductors up to 2.0″ (50 mm) in diameter
- “Third hand” – test probe holder
- Rubber over-molded case with built-in probes storage
Close
Fluke Amprobe AC68C TRMS 600 A Clamp Meter
- 8 functions/11 ranges
- Data and AC peak hold
- DC auto zero
- Carrying case included
- 33⁄4 digit, LCD, max reading of 3999
- Maximum jaw opening 1.57˝ (40 mm)
- Autoranging for frequency measurement
- Low battery indication
- Auto-power off after 30 minutes
- Manual function and range selection with rotary selector
Close
Amprobe ACD-10 TRMS-PLUS 600 A Clamp Multimeter
- AC/DC Voltage to 600 V
- AC Current to 600 A
- Thin jaws, only 0.4″ (10 mm) thick
- Resistance to 40 MΩ
- Continuity buzzer
- Capacitance to 3000 uF
- Frequency measurement
- In rush current
- Hold maximum reading functions
- Accommodates conductors up to 1.02″ (26 mm) in diameter
- Auto ranging
- Auto power off
- Rubber over-molded case
- Overload protected
- True-rms measurement
