Previous product
Back to products
Amprobe NCV-1040 Non-Contact Voltage Probe
$92.00
Excluding GST 10%
Next product
Fluke Amprobe PM55A Pocket Multimeter with VolTect™ Non-Contact Voltage Detection
$179.00
Excluding GST 10%
Amprobe PM51A Pocket Digital Multimeter
$81.00Excluding GST 10%
- Measures AC and DC voltage, resistance, continuity with beeper, capacitance and frequency
- Fully autoranging with 7 measurement functions and 27 ranges
- Large oversize digital display with measurement results and the unit icon
- Data hold freezes measurement value
- Average sensing
- Power consumption (typical) 2 mA
- Automatic power off (idle for 30 minutes)
- APO consumption (typical) 2.2 μA
- E.M.C. meets EN61326
- Audible continuity tester open circuit voltage 0.4 V DC typical
- Diode tester test current (typical) 0.25 mA
- Diode tester open circuit voltage 1.6 V DC
Available on backorder
Related products
Close
Fluke Amprobe 35XP-A Digital Multimeter with Temperature
- Temperature measurement capability to 1000 °C/1832 °F (type-K thermocouple included)
- 600 V AC/600 V DC – highest voltage rating in this class of meter
- Capacitance for motor run/start test
- 0.1 μA resolution for flame sensor testing
- Frequency to 1 MHz
- Resistance to 40 MΩ
- Data hold freezes display
- Magne-Grip™ Holster
- VolTect™ non-contact voltage detector
- Low battery indication
Close
Amprobe ALC-110 Leakage Current Clamp
-
Product Features:
- Measures:
- Earth and differential leakage currents
- Leakage currents through the earth (PE) conductor
- Appliance current consumption without interruptions to the circuit
- Low influence of external low frequency magnetic fields: @ IN: 3.500 mA – 600.0 mA ≤ 30 A/m, operating class 2
- True-RMS measurements for accuracy when measuring complex, non-sinusoidal waveforms
- Mechanical jaw lock with 1.2 in. (30 mm) opening assures accuracy of low current measurements
- Highest resolution of 0.001 mA while measuring up to 60 A
- Broad frequency range 15 Hz to 1 kHz
- Selectable filters:
- Low Pass 50/60Hz filter to perform measurements on equipment driven by Variable Frequency Drives (VFDs) or affected by high frequency noise
- Appliance Filter to conduct leakage current measurements on appliances
- No filter
- Selectable limits: 0.25 mA, 0.5 mA, 3.5 mA, 10 mA, 12 mA
- Max readings and hold function
- High safety rating: CAT III 600 V
- Battery-saving design with an auto backlight off and auto power off
Applications
- Trace the source of earth leakage current
- Identify intermittent GFCI trips without switching equipment off
- Check a system for an electrical break of insulation where current is flowing to the ground
- Where industrial leakage current testing is required
- Measures:
Close
Fluke Amprobe AM-140-A Precision TRMS Digital Multimeters with PC Connection
- Features
- True RMS (TRMS)
- Measurements: Voltage up to 1000V AC/DC, Resistance, AC/DC Current, Frequency, Capacitance, Duty Cycle
- Optical isolated PC interface capability
- Crest (Peak hold), MAX, MIN MAX-MIN recording
- Auto and manual ranging
- Intelligent auto power off
- Data hold
- Relative zero mode
- Audible and visual warning against improper plug-in
- DC Loop Current 4-20mA
- dBm reading with 20 selectable impedance values
- Backlight display
- Large, easy to read large LCD display
- High speed analog bar graph
- Diode Test
- 4-20mA DC loop current
- Audible continuity
- Safety CAT IV 600V, CAT III 1000V
Close
Fluke Amprobe ACDC-100 1000 A AC/DC Clamp Meter
- Large, easy to read LCD display
- Auto and manual ranging
- Relative zero mode
- Auto power off
- Data hold
- MAX capture function for inrush current measurements (30 mS response)
- Diode test
- Audible continuity
- Accommodates conductors up to 2.0″ (50 mm) in diameter
- “Third hand” – test probe holder
- Rubber over-molded case with built-in probes storage
Close
Fluke Amprobe 37XR-A TRMS Digital Multimeter
- Backlight, True-rms with component and logic test
- Inductance to 40 H, frequency to 40 MHz, capacitance to 400 μF, logic to 20 MHz
- Input warning tone when test leads are in wrong jack
- 10 Amps AC/DC, fully safety fused
- Continuity beeper
- Min/max, average, relative, peak, and data hold
- Auto power off to save battery life
- Separate door for easy battery and fuse access
- Magne-Grip™ Holster with magnetic hanging strap
- Autoranging; display: 4-3/4 digit LCD, 10,000 counts with 41-segment analog bar graph
- Display Update Rate: 2/sec, nominal
- Power Battery: 9 V NEDA 1604, JIS 006P, IEC 6F22
- Operating temperature: 0 °C to 45 °C at < 70 % R.H
Close
Fluke Amprobe ACD-6 PRO Digital Clamp Meter 600 V AC/DC
-
Product Features:
- AC current to 1000A
- AC and DC voltage to 600V
- Resistance
- Continuity beeper
- Diode test
- Relative zero mode
- Auto and manual ranging
- Auto power off
- Data hold
- Large, easy to read LCD display
- Accommodates conductors up to 1.77″ (45mm) in diameter
Close
Fluke Amprobe ACD-10 PLUS 600A Clamp Multimeter
Amprobe ACD-10 PLUS 600A Clamp Multimeter
- Measures AC and DC voltage to 600V and AC current to 600A to handle residential/commercial and small industrial applications
- Thin jaws, only 10mm (0.4″) thick make it easier to maneuver between tightly packed conductors
- Measures frequency, resistance, and capacitance
- Features continuity beeper to quickly find opens and shorts
- Accommodates conductors up to 1.0″ (25mm) in diameter
- Auto ranging saves time by instantly selecting correct range
- Auto power off to conserve battery life
- Rubber over-molded case absorbs shock
- Includes test leads, battery (installed), soft carrying pouch, and users manual
Close
Fluke Amprobe AC68C TRMS 600 A Clamp Meter
- 8 functions/11 ranges
- Data and AC peak hold
- DC auto zero
- Carrying case included
- 33⁄4 digit, LCD, max reading of 3999
- Maximum jaw opening 1.57˝ (40 mm)
- Autoranging for frequency measurement
- Low battery indication
- Auto-power off after 30 minutes
- Manual function and range selection with rotary selector
