This secondary PRT has a -200 to 670°C range, as well as an INFO-CON connection for 1523 and 1524 models.
Previous product
Back to products
Fluke 5609-9BND-S Secondary PRT with 90° Bend and Spade Lugs, Calibration Options
$2,360.00
Excluding GST 10%
Next product
Fluke 5609-15-P Secondary PRT with INFO-CON for 1523/1524 Models, 6ft Lead, Calibration Options
$2,226.00
Excluding GST 10%
Fluke 5609-12-P Secondary PRT with INFO-CON for 1523/1524 Models, -200 to 670°C, Calibration Options
$2,075.00Excluding GST 10%
Features
- -328 to 1,238°F (-200 to 670°C) (3.94in (100mm) minimum immersion)
- ±0.01 short-term stability
- Calibration not included, NVLAP-accredited calibration optional, lab code 200348-0
Available on backorder
Related products
Close
Fluke 190 Series II 100MHz 4 Channel ScopeMeter Oscilloscope
Features
- Four independent isolated input channels
- 60, 100, 200 and 500 MHz bandwidths
- Sample rate: Up to 2.5 GS/s
- Sample rate resolution: Up to 400 ps
- Deep memory: 10,000 point per trace waveform capture
- CAT III 1000 V / CAT IV 600 V safety rating
- Seven hour, high performance Li-ion batteries
- Battery door for convenient battery access
- Isolated USB ports for memory devices and PC connectivity
Close
Fluke BT-520 Battery Analyzer
Key features
Fluke BT510 key features:
- Battery Voltage – During the internal resistance test, Fluke Battery Analyzers also measure the voltage of the battery under test
- Discharge Volts – The Discharge mode collects the voltage of each battery multiple times at a user defined interval during a discharge or load test. Users can calculate the time a battery takes to drop to the cut-off voltage and use this time to determine the capacity loss of the battery
- Ripple Voltage Test – Measures unwanted residual ac component of the rectified voltage in dc charging and inverter circuits. Allows users to test ac components in dc charging circuits and find one of the root causes of battery deterioration
- Meter and Sequence Modes – The Meter mode is used for a quick test or troubleshooting. In this mode you can save and read the readings in a measurement or time sequence. The Sequence mode is for maintenance tasks with multiple power systems and battery strings. Before a task starts, users can configure a profile for the task for data management and report generation
- Threshold and Warning – Users can configure a maximum of 10 sets of thresholds and receive a Pass/ Warning/ Fail indication after each measurement
- Intercell Strap Resistance Test and Data Management – Measures the resistance of the intercell connection between batteries in a string. Once the measurements are completed Fluke Battery Management Software version 1.0.69 can now report the strap resistance for a battery string or historical data over time.
- AutoHold – When AutoHold is turned on, a reading is captured when it remains stable for 1 second. The reading is then released when a new measurement starts
- AutoSave – When AutoSave is turned on, measured values are saved to internal memory automatically after an AutoHold reading is captured
Close
Fluke DS703 FC Diagnostic Videoscope
Key features
- High definition probe with dual-view camera
- Processing speeds that render a smooth, clear, consistent image
- 7” LCD screen for easy viewing
- Macro to micro zoom function
- Adjustable lighting to capture the best image
- Up is Up® technology for an appropriate orientation, regardless of the probe location
- Fluke Connect® allows you to save and share images directly from the diagnostic scope
Close
Fluke 1503 Insulation Resistance Tester
Key features
- A rugged, compact insulation resistance tester for residential and commercial electricians
- Performs insulation tests from 0.01 MΩ to 2000 MΩ
- Offers two insulation test voltages: 500 V and 1000 V
- Includes live circuit detection to prevent insulation test if voltage >30 V is detected
- Measures resistance from 0.01 Ω to 20.00 kΩ
Close
Fluke 1555 FC w/IR3000FC 10 kV Insulation Tester with IR3000 FC Connector
Features
- Test voltages to up 10 kV and save time by trending on the spot only with Fluke Connect™
- CAT III 1000 V, CAT IV 600 V safety rating
- Warning function alerts the user that line voltage is present and gives the voltage reading up to 600 V AC or DC for increased user safety
- Selectable test voltages in 50 V steps from 250 V to 1000 V, and 100 V steps above 1000 V
- Measurements can be stored in up to 99 memory locations, with each location assigned a unique, user defined, label for easy recall
- Long battery life gives the user over 750 tests between charges
- Automatic calculation of Dielectric Absorption (DAR) and Polarization Index (PI) with no additional setup
- Guard system eliminates the effect of surface leakage current on high-resistance measurements
- Large digital/analog LCD for easy viewing
- Capacitance and leakage current measurement
- Ramp function for breakdown testing
- Resistance measurements up to 2 TΩ
- Timer settings up to 99 minutes for timed tests
- 3-year warranty
Close
Fluke 1663 Multifunction Installation Tester
Features
- 500V AC/DC voltage measurement TRMS
- 0.1V resolution & 3.3MΩ input impedance
- 660V RMS overload protection
- 20, 200, & 2000Ω auto-ranging continuity test
- 0.01, 0.1, & 1Ω resolution
- >4V open circuit voltage
- L-N, L-PE, N-PE inputs
- 50, 100, 250, 500, & 1000V insulation test voltages
- Test smooth DC sensitive RCDs (Type B/B+)
- 200 & 2000Ω earth resistance test
- 0.1 & 1Ω resolution
- 125Hz frequency & 25V output voltage
- On/Off switchable auto-start for RCD & Looptest
- Time & date (with optional FlukeView software)
- IP40 rated housing
- Complies with IEC/EN, UL, ANSI/ISA, & CAN/CSA
Close
Fluke 1736/EUS Three-Phase Power Loggers
Key features
- Versatile, three-phase Fluke Connect-compatible power logger for conducting basic energy and power quality studies
- Automatically captures and logs voltage, current, power, harmonics and associated power quality values.
- Provides the highest safety rating in the industry: 600 V CAT IV/1000 V CAT III rated for use at the service entrance and downstream
- Automatically logs all measured values and stores more than 20 separate logging sessions
Close
Fluke 123B Industrial ScopeMeter® Hand-Held Oscilloscope, 20 MHz
Features
- Dual-input digital oscilloscope and multimeter
- 20 MHz oscilloscope bandwidth
- Two 5000-count True RMS digital multimeters
- Connect-and-View™ trigger simplicity for hands-off operation
- IntellaSet™ technology automatically and intelligently adjusts numerical readout based on the measured signal
- Dual-input waveform and meter reading recorder for trending data over extended periods
- Recorder Event Detect captures elusive intermittent signals on repetitive waveforms up to 4 kHz
- Shielded test leads for oscilloscope, resistance and continuity measurements
- Resistance, continuity, diode and capacitance meter measurements
- Power measurements (W, VA, VAR, PF, DPF, Hz)
- Voltage, current and power harmonics
- Check Industrial networks with BusHealth physical layer tests against defined reference levels
- Save or recall data and instrument setups
- Store instrument setups defined by a test sequence for routine maintenance or most often used test procedures
- External optically isolated USB interface to transfer, archive and analyze scope or meter data
- Optional WiFi adapter connected to internal USB port to wirelessly transfer information to the PC, laptop or Fluke Connect® mobile app
- FlukeView® ScopeMeter® Software for Windows®
- Rugged design to withstand 3g Vibration, 30g shock, and rated IP51 according to EN/IEC60529
- Highest safety rating in the industry: safety rated for CAT IV 600 V
