The Fluke 80K-40 High Voltage AC/DC Probe, 40,000V AC/DC is designed to extend the voltage measuring capability of an AC/DC voltmeter to 40,000 volts (peak AC, or DC Overvoltage Category I). This probe can only be used to make measurements on energy limited circuits within equipment, such as televisions or photo copy machines. The probe provides high accuracy when used with a voltmeter having 10 Megohm input impedance. Note: Do NOT use this probe to measure high voltages on power distribution systems.
Previous product
Back to products
Fluke 80K-15 High Voltage Probe
$597.00
Excluding GST 10%
Next product
Fluke 80K-6 KV High Voltage Probe
$292.00
Excluding GST 10%
Fluke 80K-40 High Voltage Probe
$508.00Excluding GST 10%
Product Features:
- Voltage range: 1kV to 40kV DC or peak AC, 28kVrms AC
- Input resistance: 1000 Megohm
- Division ratio: 1000:1
- Safety rating(s): IEC 1010-2-031:1993, Type B, 40kV DC or peak AC, 28kVrms AC, Overvoltage Category I (voltages derived from limited energy transformer)
- Required meter input resistance: 10 Megohm
Available on backorder
Related products
Close
Fluke 190 Series II 200MHz 4 Channel ScopeMeter Oscilloscope
Features
- Four independent isolated input channels
- 60, 100, 200 and 500 MHz bandwidths
- Sample rate: Up to 2.5 GS/s
- Sample rate resolution: Up to 400 ps
- Deep memory: 10,000 point per trace waveform capture
- CAT III 1000 V / CAT IV 600 V safety rating
- Seven hour, high performance Li-ion batteries
- Battery door for convenient battery access
- Isolated USB ports for memory devices and PC connectivity
Close
Fluke 1503 Insulation Resistance Tester
Key features
- A rugged, compact insulation resistance tester for residential and commercial electricians
- Performs insulation tests from 0.01 MΩ to 2000 MΩ
- Offers two insulation test voltages: 500 V and 1000 V
- Includes live circuit detection to prevent insulation test if voltage >30 V is detected
- Measures resistance from 0.01 Ω to 20.00 kΩ
Close
Fluke BT-520 Battery Analyzer
Key features
Fluke BT510 key features:
- Battery Voltage – During the internal resistance test, Fluke Battery Analyzers also measure the voltage of the battery under test
- Discharge Volts – The Discharge mode collects the voltage of each battery multiple times at a user defined interval during a discharge or load test. Users can calculate the time a battery takes to drop to the cut-off voltage and use this time to determine the capacity loss of the battery
- Ripple Voltage Test – Measures unwanted residual ac component of the rectified voltage in dc charging and inverter circuits. Allows users to test ac components in dc charging circuits and find one of the root causes of battery deterioration
- Meter and Sequence Modes – The Meter mode is used for a quick test or troubleshooting. In this mode you can save and read the readings in a measurement or time sequence. The Sequence mode is for maintenance tasks with multiple power systems and battery strings. Before a task starts, users can configure a profile for the task for data management and report generation
- Threshold and Warning – Users can configure a maximum of 10 sets of thresholds and receive a Pass/ Warning/ Fail indication after each measurement
- Intercell Strap Resistance Test and Data Management – Measures the resistance of the intercell connection between batteries in a string. Once the measurements are completed Fluke Battery Management Software version 1.0.69 can now report the strap resistance for a battery string or historical data over time.
- AutoHold – When AutoHold is turned on, a reading is captured when it remains stable for 1 second. The reading is then released when a new measurement starts
- AutoSave – When AutoSave is turned on, measured values are saved to internal memory automatically after an AutoHold reading is captured
Close
Fluke 1555 FC w/IR3000FC 10 kV Insulation Tester with IR3000 FC Connector
Features
- Test voltages to up 10 kV and save time by trending on the spot only with Fluke Connect™
- CAT III 1000 V, CAT IV 600 V safety rating
- Warning function alerts the user that line voltage is present and gives the voltage reading up to 600 V AC or DC for increased user safety
- Selectable test voltages in 50 V steps from 250 V to 1000 V, and 100 V steps above 1000 V
- Measurements can be stored in up to 99 memory locations, with each location assigned a unique, user defined, label for easy recall
- Long battery life gives the user over 750 tests between charges
- Automatic calculation of Dielectric Absorption (DAR) and Polarization Index (PI) with no additional setup
- Guard system eliminates the effect of surface leakage current on high-resistance measurements
- Large digital/analog LCD for easy viewing
- Capacitance and leakage current measurement
- Ramp function for breakdown testing
- Resistance measurements up to 2 TΩ
- Timer settings up to 99 minutes for timed tests
- 3-year warranty
Close
Fluke 1507 Insulation Resistance Tester
Key features
- Rugged, compact advanced insulation resistance tester for electrical contractors and industrial and commercial electricians
- Automatically calculates Polarization Index and Dielectric Absorption Ratio
- Makes repetitive tests simple and easy with a Compare (Pass/Fail) function
- Offers multiple insulation test voltages: 50 V, 100 V, 250 V, 500 V, and 1000 V
Close
Fluke 424D Laser Distance Meter
Professional-grade, automated endpiece correction, 80m/260ft range
Features
- Reduction of estimation errors
- Range: 80m/260ft
- Max range: 100m (330ft)
- Inclination sensor for taking measurements in hard to reach areas
- Compass provides a “heading” for distance measurement
- Automated endpiece correction
- Advanced laser technology for distance measurement
- Instant measurement with one-button operation
- Quick calculation of area (square footage) and volume
- Minimum/maximum function
- Improved battery life from automatic shut-off feature
- Enhanced Pythagoras calculation
- Tripod mode
- Stake out function
- Audible keypad feedback
- Storage of the last twenty measurements for quick recall of distance
- IP54 protection
Close
Fluke 1738/B Three-Phase Power Loggers
Key features
- Three-phase advanced Fluke Connect compatible-power logger for making critical power quality and energy decisions in real-time
- Automatically captures and logs voltage, current, power, harmonics and associated power quality values.
- Provides the highest safety rating in the industry: 600 V CAT IV/1000 V CAT III rated for use at the service entrance and downstream
- Automatically logs all measured values and stores more than 20 separate logging sessions
Close
Fluke DS703 FC Diagnostic Videoscope
Key features
- High definition probe with dual-view camera
- Processing speeds that render a smooth, clear, consistent image
- 7” LCD screen for easy viewing
- Macro to micro zoom function
- Adjustable lighting to capture the best image
- Up is Up® technology for an appropriate orientation, regardless of the probe location
- Fluke Connect® allows you to save and share images directly from the diagnostic scope
