Fluke 810PA Power Adapter with international plug set for the 810.
Previous product 
Back to products Fluke 810 Vibration Tester - Quick Disconnect Cable Original price was: $293.00.$264.00Current price is: $264.00.
Excluding GST 10%
Next product 
Fluke 810S Triaxial Vibration Sensor for the 810 Original price was: $2,941.00.$2,647.00Current price is: $2,647.00.
Excluding GST 10%
Fluke 810PA Power Adapter with international plug set for the 810
$166.00Excluding GST 10%
Available on backorder
Related products
Fluke TL175 TwistGuard Test Leads
Features
- Extra-heavy duty strain relief on probe and plug
- Tested beyond 30,000 bends without failure
- -4 to 131°F (-20 to 55°C) operating temp
- Altitude of 6562ft (2000m)
- CAT II 1000V, CAT III 1000V, CAT IV 600V rated
- 10A max, Pollution Degree 2
- Conforms to EN61010-031
- 1-year warranty
Fluke TL26A Test Lead Set
Product Features:
- U-shaped nose for blade-shaped terminals
- Notched jaw for gripping screw heads, bare wire or terminals
- Serrated teeth for gripping threaded or wire-wrapped terminals
- Cluster of sharp needles for piercing small gauge wires (#22-#28 AWG)
- Large piercing needle for penetrating larger gauge wires
Fluke TL935 Patch Cords
Fluke TL935 Offers
- 3 sets (red and black pairs) of multi-stacking 4 mm banana plug patch cords
- Nickel-plated banana plugs
- 60 cm, 90 cm, 120 cm long PVC insulated leads
- 30 V rms or 60 V DC, 15 A
- One year warranty
- 1 – Patch Cord, 60 cm (Red)
- 1 – Patch Cord, 60 cm (Black)
- 1 – Patch Cord, 90 cm (Red)
- 1 – Patch Cord, 90 cm (Black)
- 1 – Patch Cord, 120 cm (Red)
- 1 – Patch Cord, 120 cm (Black)
-11%
Close
AC288 Terminal Block Probe with Retractable Probe Tip
Key features
- Retractable probe tip designed for increased safety, while providing flexibility to reach deep connection points
- Recommended for use with TL224, TL222 or TL221 Test Leads
- 11.5 cm (4.5 in) insulated, flexible shaft
- 1 mm diameter probe tip extends out to 8.4 mm (0.33 in) length
- Retractable probe tip is made with stainless steel
- Safety rated: IEC 61010-031 Ed.1.12008, CAT III 1000 V, CAT IV 600 V
- Operating temperature: -20 °C to 55 °C (-4 °F to 131 °F), 90% RH
- One-year warranty
Fluke TL222 Test Leads
Features
- Designed to improve steadiness in slippery hands
- Rubber overmolded surfaces and finger-hugging curves
- Reinforced strain relief
- CAT IV 600V & CAT III 1000V safety rating
- 10A rating
- UL listed
- 1-year warranty
-10%
Close
Fluke AC89 Piercing Test Clip
Product Features:
- Single probe pierces 0.25 to 1.5 mm insulated wire
- Small pin allows self-healing of insulation
- Safety rating(s): CAT IV 600V, CAT III 1000V, 5A rating
- UL listed
Fluke TL71 Test Lead Set
Fluke TL71 Offers
Test leads are an integral part of the complete measurement system and extend the capabilities of your digital multimeter. The TL71 premium test lead set has one pair of red and black comfort grip probes with flexible silicone-insulated, right-angle test leads. With distinctive comfort grip probes, they are heat and cold resistant with safety ratings up to CAT III 1000 V.
Features
- One pair (red, black) comfort grip probes with silicone insulated, right-angle test leads
- Recommended for µV measurements
- CAT II 1000 V, 10 A rating
- CAT III 1000 V, CAT IV 600V only with protective cap
- One year warranty
Applications
- Test and measurement
- Oil and gas
- R&D
- Electronics design
- Electronics service
- Repair and maintenance
- Electrical
- Industrial
-10%
Close
Fluke AC220 Alligator Clips
Product Features:
- Rubber overmolded surfaces and finger-hugging curves for comfortable, reliable grip
- Small, insulated, nickel-plated jaws
- Blunt tip grabs round screw heads up to 9.5 mm
- Safety rating(s): CAT IV 600V, CAT III 1000V, 10A rating
- UL listed
- For use with Models TL222 and TL224
