Fluke 810PA Power Adapter with international plug set for the 810.
Previous product
Back to products
Fluke 810 Vibration Tester - Quick Disconnect Cable
$293.00
Excluding GST 10%
Next product
Fluke 810S Triaxial Vibration Sensor for the 810
$2,941.00
Excluding GST 10%
Fluke 810PA Power Adapter with international plug set for the 810
$166.00Excluding GST 10%
Available on backorder
Related products
Close
AC288 Terminal Block Probe with Retractable Probe Tip
Key features
- Retractable probe tip designed for increased safety, while providing flexibility to reach deep connection points
- Recommended for use with TL224, TL222 or TL221 Test Leads
- 11.5 cm (4.5 in) insulated, flexible shaft
- 1 mm diameter probe tip extends out to 8.4 mm (0.33 in) length
- Retractable probe tip is made with stainless steel
- Safety rated: IEC 61010-031 Ed.1.12008, CAT III 1000 V, CAT IV 600 V
- Operating temperature: -20 °C to 55 °C (-4 °F to 131 °F), 90% RH
- One-year warranty
Close
Fluke TP175 TwistGuard™ Test Probes 2mm Diameter Probe Tips
Key features
- Patented TwistGuard™ extendable tip shroud meets the highest electrical safety requirements to reduce tip exposure while providing the versatility needed for most measurements
- Ratings: CAT II 1000 V, CAT III 1000 V, CAT IV 600 V, 10 A max., Pollution Degree 2
Close
Fluke AC175 Alligator Clip Set
Product Features:
- Slide-on alligator clips
- Clip jaws provide 8 mm opening with flexible boots
- Compatible with 4 mm banana plugs and test leads
- Safety rating(s): CAT IV 600V, CAT III 1000V, 10A
- For use with Models TL71, TL75, TL175 and TP175
Close
Fluke AC220 Alligator Clips
Product Features:
- Rubber overmolded surfaces and finger-hugging curves for comfortable, reliable grip
- Small, insulated, nickel-plated jaws
- Blunt tip grabs round screw heads up to 9.5 mm
- Safety rating(s): CAT IV 600V, CAT III 1000V, 10A rating
- UL listed
- For use with Models TL222 and TL224
Close
Fluke TL26A Test Lead Set
Product Features:
- U-shaped nose for blade-shaped terminals
- Notched jaw for gripping screw heads, bare wire or terminals
- Serrated teeth for gripping threaded or wire-wrapped terminals
- Cluster of sharp needles for piercing small gauge wires (#22-#28 AWG)
- Large piercing needle for penetrating larger gauge wires
Close
Fluke AC89 Piercing Test Clip
Product Features:
- Single probe pierces 0.25 to 1.5 mm insulated wire
- Small pin allows self-healing of insulation
- Safety rating(s): CAT IV 600V, CAT III 1000V, 5A rating
- UL listed
Close
Fluke TL175 TwistGuard Test Leads
Features
- Extra-heavy duty strain relief on probe and plug
- Tested beyond 30,000 bends without failure
- -4 to 131°F (-20 to 55°C) operating temp
- Altitude of 6562ft (2000m)
- CAT II 1000V, CAT III 1000V, CAT IV 600V rated
- 10A max, Pollution Degree 2
- Conforms to EN61010-031
- 1-year warranty
Close
Fluke AC283 Pincer Clips
Features
- 1A rating
- Use for continuity testing on circuit board components
- 4.49in (11.4cm) flexible insulated shaft
- CAT IV 600V, CAT III 1000V safety rated
- UL listed
- 1-year warranty
