Fluke 810QDC Quick Disconnect Cable for the Fluke 810.
Previous product
Back to products
Fluke 805ES - EXTERNAL VIBRATION SENSOR
$2,080.00
Excluding GST 10%
Next product
Fluke 810PA Power Adapter with international plug set for the 810
$166.00
Excluding GST 10%
Fluke 810 Vibration Tester – Quick Disconnect Cable
$293.00Excluding GST 10%
Available on backorder
Related products
Close
Fluke H900 Test Lead Holder
Features
- Mounting holes for securing to wall or surface
- 10.98 x 3.5 x 1.26 inches (27.9 x 8.9 x 3.2 cm)
- 1-year warranty
Close
Fluke TL71 Test Lead Set
Fluke TL71 Offers
Test leads are an integral part of the complete measurement system and extend the capabilities of your digital multimeter. The TL71 premium test lead set has one pair of red and black comfort grip probes with flexible silicone-insulated, right-angle test leads. With distinctive comfort grip probes, they are heat and cold resistant with safety ratings up to CAT III 1000 V.
Features
- One pair (red, black) comfort grip probes with silicone insulated, right-angle test leads
- Recommended for µV measurements
- CAT II 1000 V, 10 A rating
- CAT III 1000 V, CAT IV 600V only with protective cap
- One year warranty
Applications
- Test and measurement
- Oil and gas
- R&D
- Electronics design
- Electronics service
- Repair and maintenance
- Electrical
- Industrial
Close
Fluke TP175 TwistGuard™ Test Probes 2mm Diameter Probe Tips
Key features
- Patented TwistGuard™ extendable tip shroud meets the highest electrical safety requirements to reduce tip exposure while providing the versatility needed for most measurements
- Ratings: CAT II 1000 V, CAT III 1000 V, CAT IV 600 V, 10 A max., Pollution Degree 2
Close
AC288 Terminal Block Probe with Retractable Probe Tip
Key features
- Retractable probe tip designed for increased safety, while providing flexibility to reach deep connection points
- Recommended for use with TL224, TL222 or TL221 Test Leads
- 11.5 cm (4.5 in) insulated, flexible shaft
- 1 mm diameter probe tip extends out to 8.4 mm (0.33 in) length
- Retractable probe tip is made with stainless steel
- Safety rated: IEC 61010-031 Ed.1.12008, CAT III 1000 V, CAT IV 600 V
- Operating temperature: -20 °C to 55 °C (-4 °F to 131 °F), 90% RH
- One-year warranty
Close
Fluke AC220 Alligator Clips
Product Features:
- Rubber overmolded surfaces and finger-hugging curves for comfortable, reliable grip
- Small, insulated, nickel-plated jaws
- Blunt tip grabs round screw heads up to 9.5 mm
- Safety rating(s): CAT IV 600V, CAT III 1000V, 10A rating
- UL listed
- For use with Models TL222 and TL224
Close
Fluke TL224 Test Leads
Product Features:
- Rubber overmolded surfaces and finger-hugging curves for comfortable, reliable grip
- Safety shrouded, standard diameter banana plugs
- Right angle connector on one end and straight connector on other end
- Reinforced strain relief
- 1.5 meter silicone-insulated wire resists heat and cold
- Safety rating(s): CAT IV 600V, CAT III 1000V, 10A
- UL listed
Close
Fluke TP80 Electronic Test Probes
Fluke TP80 Offers
- One pair (red, black)
- IC insulated cap prevents shortening of IC legs for probing high density components or boards
- CAT III 1000 V, 10 A rating. UL listed
- One year warranty
Close
Fluke TL175 TwistGuard Test Leads
Features
- Extra-heavy duty strain relief on probe and plug
- Tested beyond 30,000 bends without failure
- -4 to 131°F (-20 to 55°C) operating temp
- Altitude of 6562ft (2000m)
- CAT II 1000V, CAT III 1000V, CAT IV 600V rated
- 10A max, Pollution Degree 2
- Conforms to EN61010-031
- 1-year warranty
