-10%
Click to enlarge
Previous product
Fluke 87V/E2 Industrial Electrician Combo Kit $1,169.00
Excluding GST 10%
Back to products
Next product
Fluke PRV240FS Proving Unit $311.00
Excluding GST 10%

Fluke 87V-MAX/E2 KIT Industrial Electrician Combo Kit

$1,227.00

Excluding GST 10%

What’s included with the Fluke 87V-MAX/E2 KIT

  • Multimeter
  • Test Leads
  • Alligator Clips
  • Test Probes
  • Meter Hanging Kit
  • Temperature Probe
  • Carrying Case
  • 9 V Battery (Installed) Removable holster with Test Lead Storage
  • 3 x AA Batteries (Installed)

Product Features:

  • IP 67 waterproof and dustproof protection, completely sealed for use in harsh environments
  • Tested to withstand 4 meter (13 feet) drop (with holster)
  • Measure up to 1000 V, up to 10 A (20 A for 30 seconds), AC and DC
  • True-RMS voltage and current for accurate measurements on non-linear signals
  • 10,000 μF capacitance range, frequency to 200 kHz
  • Extended AC voltage bandwidth- 15 Hz to 20 kHz
  • Low-pass filter for accurate voltage and frequency measurements on adjustable speed motor drives and other electrically noisy equipment
  • Built in thermometer conveniently allows users to take temperature readings without having to carry a separate instrument
  • Min/Max/Average recording, plus 150 μs Peak min-max to capture variations automatically
  • Resistance, continuity and diode test
  • Large display digits and 2 level bright white backlight with backlit keypad buttons
  • Hi resolution 20,000 count display mode
  • Relative mode to remove test lead resistance from low ohms measurements
  • Reversible holster for added protection when not in use
  • Withstands hazardous 8,000 volt spikes caused by load switching and faults on industrial circuits
  • Long battery life (800 hours)
  • Safety rated CAT IV 600 V/CAT III 1000 V
  • Battery type: Three AA batteries
  • Kit includes soft carrying case, probes and magnetic hanging kit

Applications

  • Industrial and facilities maintenance
  • Cement plants and electrical utilities
  • Food processing and chemical processing
  • Steel mills and foundries
  • Mining (MHSA approval pending)
  • Military, petrochemical

Available on backorder

SKU: 5160712 Categories: ,
Overview

Built around this True RMS digital multimeter, this kit is ideal for industrial electricians. You can troubleshoot a wide variety of electrical problems and, it features an IP 67 rating. Additionally, the included accessories are designed to increase your productivity.

IP67 rated

Fully waterproof and dust proof, to work reliably in all the places that you need to work.

Withstands drops to 13′ (4 m)

A rugged digital multimeter which is built with an industrial strength case and a removable holster. The holster doubles as a test probe holder for one-handed operation.

Withstands heat and cold

The meter has an extended operating temperature range of -40°F (-40°C) for up to 20 minutes to 131°F (55°C).

Fluke TL224 SureGrip™ Silicone Insulated Test Leads. Features:

  • DMM test leads (red, black) with safety shrouded, standard diameter banana plugs
  • Right angle connector on one end and straight connector on the other
  • Reinforced strain relief
  • 4.9′ (1.5 m) silicone-insulated wire resists heat and cold
  • CAT IV 600 V, CAT III 1000 V, 10 A rating; CSA listed

Fluke AC220 SureGrip™ Alligator Clips. Features:

  • One pair (red, black) of small, insulated, nickel plated jaws
  • Blunt tip grabs round screw heads up to 0.37″ (9.5 mm)
  • CAT IV 600 V, CAT III 1000 V, 10 A rating; CSA listed

Fluke TL238 SureGrip™ Test Lead Set for high energy environments. Features:

  • 0.15″ (4 mm) of exposed metal at the tip
  • Probe extenders fit between modular test leads and test probes, increasing the distance between you and a live circuit by 8″ (20.5 cm)
  • Conform to safety standard IEC 1010-2-031, maximum 1000 V CAT III, 600 V CAT IV, Pollution Degree 2, 10 A
  • Probe extenders conform to safety standard IEC 1010-2-031, maximum 1000 V CAT III, Pollution Degree 2, 10 A

Fluke TPAK ToolPak Magnetic Meter Hanger. Features:

  • Powerful magnetic hanger allows you to hang your meter on any metallic surfaces
  • 9″ (228.6 mm) hook and loop strap allows you to loop around pipes
  • Hook hanger for hanging on non-magnetic surfaces
  • General purpose hanger allows you to hang your meter on nails, hooks and many other objects
  • Compatible with many Fluke instruments

Fluke 80BK-A Integrated DMM Temperature Probe. Features:

  • Standard shrouded banana jack
  • Convenient one piece construction

Fluke C35 Soft Carrying Case. Features:

  • The top opens laterally to allow use of test tool without removing it from the case
  • Velcro® strap to secure the test tool
  • Durable polyester 600D