Expands the measurement range of the select Fluke meters to 2500 A AC, and connects directly to the meter, displaying current measurements without error prone scaling factors. The 6′ cord allows separation between the measurement location and the clamp meter, and the large loop size and thin cross-section allow the measurement of awkward sized conductors and improved wire access in crowded spaces.
Previous product
Back to products
Fluke Amprobe 38SW-A RS232 Software/Cable
$87.00
Excluding GST 10%
Next product
Fluke i2500-10 iFlex Flexible 10" Current Probe
$300.00
Excluding GST 10%
Fluke i2500-18 iFlex Flexible Current Probe, 18″
$300.00Excluding GST 10%
Fluke i2500-18 Offers
Features
- Expands the measurement range to 2500 A AC while providing increased display flexibility, ability to measure awkward sized conductors and improved wire access
- CAT IV 600 V, CAT III 1000 V
- 0.29″ (7.5 mm) coil diameter allows measurement in tight spaces
- Ergonomic design allows easy operation with one hand
- 6′ (1.8 m) cable
Measurement capability
- 2500 A AC current measurement with select Fluke meters
- Works with frequency, inrush, and min/max functions on select Fluke meters
Available on backorder
Related products
Close
Fluke BT-520 Battery Analyzer
Key features
Fluke BT510 key features:
- Battery Voltage – During the internal resistance test, Fluke Battery Analyzers also measure the voltage of the battery under test
- Discharge Volts – The Discharge mode collects the voltage of each battery multiple times at a user defined interval during a discharge or load test. Users can calculate the time a battery takes to drop to the cut-off voltage and use this time to determine the capacity loss of the battery
- Ripple Voltage Test – Measures unwanted residual ac component of the rectified voltage in dc charging and inverter circuits. Allows users to test ac components in dc charging circuits and find one of the root causes of battery deterioration
- Meter and Sequence Modes – The Meter mode is used for a quick test or troubleshooting. In this mode you can save and read the readings in a measurement or time sequence. The Sequence mode is for maintenance tasks with multiple power systems and battery strings. Before a task starts, users can configure a profile for the task for data management and report generation
- Threshold and Warning – Users can configure a maximum of 10 sets of thresholds and receive a Pass/ Warning/ Fail indication after each measurement
- Intercell Strap Resistance Test and Data Management – Measures the resistance of the intercell connection between batteries in a string. Once the measurements are completed Fluke Battery Management Software version 1.0.69 can now report the strap resistance for a battery string or historical data over time.
- AutoHold – When AutoHold is turned on, a reading is captured when it remains stable for 1 second. The reading is then released when a new measurement starts
- AutoSave – When AutoSave is turned on, measured values are saved to internal memory automatically after an AutoHold reading is captured
Close
Fluke DS703 FC Diagnostic Videoscope
Key features
- High definition probe with dual-view camera
- Processing speeds that render a smooth, clear, consistent image
- 7” LCD screen for easy viewing
- Macro to micro zoom function
- Adjustable lighting to capture the best image
- Up is Up® technology for an appropriate orientation, regardless of the probe location
- Fluke Connect® allows you to save and share images directly from the diagnostic scope
Close
Fluke 1503 Insulation Resistance Tester
Key features
- A rugged, compact insulation resistance tester for residential and commercial electricians
- Performs insulation tests from 0.01 MΩ to 2000 MΩ
- Offers two insulation test voltages: 500 V and 1000 V
- Includes live circuit detection to prevent insulation test if voltage >30 V is detected
- Measures resistance from 0.01 Ω to 20.00 kΩ
Close
Fluke 1662 – Multifunction Electrical Tester
A solid, reliable, basic installation tester
- Tests voltage and frequency
- Checks wiring polarity to detect broken N wires
- Measures insulation resistance and loop and line resistance
- Measures motor windings with continuity test
- Calculates prospective earth fault current (PEFC/IK) and prospective short-circuit current (PSC/IK)
Close
Fluke 190 Series II 60MHz ScopeMeter Oscilloscope
Features
- Four independent isolated input channels
- 60, 100, 200 and 500 MHz bandwidths
- Sample rate: Up to 2.5 GS/s
- Sample rate resolution: Up to 400 ps
- Deep memory: 10,000 point per trace waveform capture
- CAT III 1000 V / CAT IV 600 V safety rating
- Seven hour, high performance Li-ion batteries
- Battery door for convenient battery access
- Isolated USB ports for memory devices and PC connectivity
Close
Fluke 190 Series II 500MHz 2 Channel ScopeMeter Oscilloscope
Features
- Four independent isolated input channels
- 60, 100, 200 and 500 MHz bandwidths
- Sample rate: Up to 2.5 GS/s
- Sample rate resolution: Up to 400 ps
- Deep memory: 10,000 point per trace waveform capture
- CAT III 1000 V / CAT IV 600 V safety rating
- Seven hour, high performance Li-ion batteries
- Battery door for convenient battery access
- Isolated USB ports for memory devices and PC connectivity
Close
Fluke 810 Vibration Tester
Features
- Plain-text diagnosis of standard faults:
- Unbalance
- Looseness
- Misalignment
- Bearing failures
- Fault severity (slight, moderate, serious, extreme)
- 200 rpm to 12000 rpm machine rotational speed range
- 5 Hz to 20 kHz Usable frequency bandwidth
- 2.56 kHz to 51.2 kHz sampling rate
- Lithium-ion, 14.8 V, 2.55 Ah battery
- 1/4 VGA, 320 × 240 color display
- Auto ranging
Close
Fluke 190 Series II 500MHz 4 Channel ScopeMeter Oscilloscope
Features
- Four independent isolated input channels
- 60, 100, 200 and 500 MHz bandwidths
- Sample rate: Up to 2.5 GS/s
- Sample rate resolution: Up to 400 ps
- Deep memory: 10,000 point per trace waveform capture
- CAT III 1000 V / CAT IV 600 V safety rating
- Seven hour, high performance Li-ion batteries
- Battery door for convenient battery access
- Isolated USB ports for memory devices and PC connectivity
