Fluke MP1-3R/1B Magnetic Voltage Probes, Three Red, One Black
Previous product
Back to products
Fluke HL-200 EX Intrinsically Safe Headlamp
$184.00
Excluding GST 10%
Next product
Kyoritsu 6205 - Portable Appliance Tester Battery Operated
$999.00
Excluding GST 10%
Fluke MP1-3R/1B – Magnetic Voltage Probes
$160.00Excluding GST 10%
Fluke MP1-3R/1B Magnetic Voltage Probes, Three Red, One Black
Available on backorder
Related products
Close
Fluke VisiFault Visual Fault Locator
- Locates visual faults including tight bends, breaks and bad connectors
- Accelerates end-to-end fiber checks
- Easily verifies polarity and identifies fibers
- Features continuous and flashing modes
- Ergonomic case survives drops, impacts and vibrations
Close
Fluke 720A Kelvin-Varley Divider (Copy)
- 0.1 ppm resolution, seven decades
- 0.1 ppm of input absolute linearity
- Built-in self calibration bridge
- Front panel self-calibration
Close
Fluke CXT280
Product Features:
- Unbreakable
- Watertight
- Airtight
- Dustproof
- Chemical resistant
- Corrosion proof
- Buoyancy allows case to float in salt water with 7.94 lb load
- Automatic purge valve for quick equalization after changes in atmospheric pressure
- Features 0.25 in neoprene O-ring and ABS latches for excellent seal
- For use with many Fluke instruments
- For use with Fluke Multimeters and Earth Ground Testers
Close
Fluke EI-162AC Clip on Current Transformer
Fluke Clip-On Current Transformer Features
- Performs selective and stakeless testing
- Inner diameter: 2 in.
- For use with Models 1623 and 1625
M1120 NST Neutral Supply Tester Kit
LCD screen to display measurement results and messages.
CAT IV 600V instrument and lead set compliance.
IP54 moisture and dust ingress rating.
Compact hand held unit housed in a lightweight heavy-duty case
Uniquely self powered passive device.
Power is taken directly from the user’s connections.
3 LED indicators and an LCD screen for status and measurement information.
An audible alarm is fitted internally as a secondary indicator. To indicate a pass at the end of the measurement cycle or a measurement failure.
Close
Fluke INDC8 – Insulated Heavy Duty Diagonal Cutter
Product Features:
- Nominal length: 8 in., 200 mm
- Cuts hard materials including steel and piano wire
- Power joint and precision cutting edges
- German CMV steel
- Designed to block potentially hazardous voltages from reaching you
- Subjected to a 10,000 V dielectric strength test, protection protection works
- Certified to 1,000 V ac and 1,500 V dc by VDE, (independent third-party lab)
- Comply to international standards such as IEC 60900 and ASTM F1505
- Critical part of NFPA 70E, which requires personal protective equipment and insulated tools rated for electrical installation
- Critical protective component between you and unplanned incident
Close
Fluke Amprobe USB-KIT2 Download Module for Amprobe Clamps
Product Features:
- Software for Transferring Data to PC
- Includes Connection Cable
- For Amprobe Clamp Meters
Close
Fluke Amprobe AT-8030 Advanced Wire Tracer Kit
Key features
- Work directly on an energized circuit without the need to take equipment offline, CAT IV 600 V rated
- Save time searching for wires hidden behind walls, ceilings and floors with the Smart Sensorâ„¢, which displays the location and orientation of energized wires
- Pinpoint wire location with the large color LCD Receiver screen
- Identify breakers and fuses, as well as the location of a break, open or short
- Non-Contact Voltage Detection utilizes passive tracing without the Transmitter to verify if a wire is energized
- Includes the CT-400 Signal Clamp accessory for inducing a tracing signal on the cable when there is no access to bare conductors
