- ADP-SC/APC SC-APC Simplex Adapter
Previous product
Back to products
Fluke Networks ADP-SC/APC SC-APC Simplex Adapter
$57.00
Excluding GST 10%
Next product
Fluke Networks QuickClean-1.25-5P Quick Clean Cleaner 1.25 mm Fiber, LC and MU, 5 Pack
$1,204.00
Excluding GST 10%
Fluke Networks ADP-SC/APC SC-APC Simplex Adapter
$57.00Excluding GST 10%
- ADP-SC/APC SC-APC Simplex Adapter
Available on backorder
Related products
Close
Fluke INDC8 – Insulated Heavy Duty Diagonal Cutter
Product Features:
- Nominal length: 8 in., 200 mm
- Cuts hard materials including steel and piano wire
- Power joint and precision cutting edges
- German CMV steel
- Designed to block potentially hazardous voltages from reaching you
- Subjected to a 10,000 V dielectric strength test, protection protection works
- Certified to 1,000 V ac and 1,500 V dc by VDE, (independent third-party lab)
- Comply to international standards such as IEC 60900 and ASTM F1505
- Critical part of NFPA 70E, which requires personal protective equipment and insulated tools rated for electrical installation
- Critical protective component between you and unplanned incident
Close
Fluke Amprobe TM-SWA CABLE AND SOFTWARE FOR TMD90 AND TMA10
Amprobe TM-SWA Cable and Software for TMD90A and TMA10A
Close
Fluke VisiFault Visual Fault Locator
- Locates visual faults including tight bends, breaks and bad connectors
- Accelerates end-to-end fiber checks
- Easily verifies polarity and identifies fibers
- Features continuous and flashing modes
- Ergonomic case survives drops, impacts and vibrations
Close
Fluke 720A Kelvin-Varley Divider
- 0.1 ppm resolution, seven decades
- 0.1 ppm of input absolute linearity
- Built-in self calibration bridge
- Front panel self-calibration
Close
Fluke Amprobe AT-8030 Advanced Wire Tracer Kit
Key features
- Work directly on an energized circuit without the need to take equipment offline, CAT IV 600 V rated
- Save time searching for wires hidden behind walls, ceilings and floors with the Smart Sensorâ„¢, which displays the location and orientation of energized wires
- Pinpoint wire location with the large color LCD Receiver screen
- Identify breakers and fuses, as well as the location of a break, open or short
- Non-Contact Voltage Detection utilizes passive tracing without the Transmitter to verify if a wire is energized
- Includes the CT-400 Signal Clamp accessory for inducing a tracing signal on the cable when there is no access to bare conductors
Close
Fluke Amprobe UAT-620 UNDERGROUND UTILITY LOCATOR KIT W/CLAMP
Product Features:
- Multiple tracing modes allow you to locate and trace energized and de-energized utilities in several applications
- Intuitive Transmitter automatically chooses correct locating function based on connected accessory and includes selectable 8/33 kHz frequencies
- Receiver’s high-contrast display allows for clear viewing in full sunlight and features automatic backlight for shaded and dark areas
- Rated CAT IV 600 V, ensuring safety when working with energized cables
- Semi-automatic gain control quickly detects tracing signal and allows precise adjustment of receiver sensitivity
- Accurate depth measurement to 20 ft
- Rugged, durable construction
- Water and dust resistant to IP54
- Drop proof to 3.28 ft (1 m)
- Signal Clamp induces signal without making electrical contact
- Ground fault locating with optional A-Frame accessory (AF-600)
- Comes as complete kit, ready for use
- Three testing modes:
- Passive power mode (50/60 Hz) – Tracing energized lines conducting current (no Transmitter necessary)
- Passive radio mode (RF) – Using surrounding radio waves to trace underground utilities (no Transmitter necessary)
- Active mode – Using UAT-600-T Transmitter
- Three active modes with UAT-600-T Transmitter:
- Induction – Transmitter will automatically start to radiate signal around it with internal antenna, used for tracing individual cables where there is no access to line to connect test leads or clamp
- Direct connection with test leads – Most reliable method to trace individual cable or pipe
- Clamp – Provides efficient and safe method of applying locate signal to cable, where it is not possible or safe to gain access to cable for making electrical contact
- Main applications:
- Locate energized 50/60 Hz cables carrying current
- Identify location of all metallic utilities, pipes* or cables (energized or de-energized)
- Trace individual pipes* or cables (energized or de-energized)
- *Tracing of non-metallic pipes and conduits is possible after inserting metal fish tape or cable
- Special applications:
- Two frequency options: 8 kHz and 33 kHz
- Locate non-metallic pipes and sewer lines
- Take depth and current measurements
- Measure voltage, resistance and output current
- Advanced locating with two people
- Locate ground faults with the AF-600 A-Frame accessory
Applications
- Commercial and Residential Construction Contractors
- Water, Gas and Electric Installation and Repair Crews
- Pipe Laying Contractors
- Cable TV and Telecommunication Companies
- Electricians and General Contractors
Close
Fluke PRV240 Proving Unit, 240V
Fluke PRV240 Offers
Reduces the risk of shock and arc flash by removing unnecessary exposure to a potentially hazardous electrical environment while verifying the functionality of test tools before and after absence or presence of voltage is checked.
Features
- Sources both AC and DC steady-state voltage – supplies 240 V DC/AC
- A single LED indicates functionality, making this unit a simple-to-use solution for verification of your test tool
- Compatible with both high impedance or low impedance multimeters, clamp meters or two pole testers
- Voltage is sourced through recessed contacts that are activated when tested probes are inserted to avoid accidental contact
- Long battery life – 5,000 tests per set of four AA batteries
Test Before Touch
Provides a safe method to verify that your electrical test tool is operating properly before you conduct further tests. The concept of “Test Before Touch” (TBT) or three point test method involves testing your meter against a known live source before and after the actual measurement. This sequence verifies that your test tool is operating properly during the actual measurement.
Designed for safety and compliance
Safe and easy method for verifying proper operation of your test tool before attempting to test for either an energized source or a de-energized source without the need for cumbersome PPE, or in cases where no known voltage source is available. Your environment may still require minimal PPE such as hard, safety glasses or earplugs when using a proving unit.
Close
Fluke Amprobe USB-KIT3 Download Module for Amprobe Precision Multimeters
Product Features:
- PC Interface Kit
- Download software with connection cable
- For Amprobe Multimeters
