For use with the 810 vibration tester.
Previous product
Back to products
Fluke 810T Non-Contact Precision Laser Tachometer for the 810
$252.00
Excluding GST 10%
Next product
Fluke 830/MAGNET Mounting Set
$2,242.00
Excluding GST 10%
Fluke SBP810 Fluke Smart Battery Pack for the 810
$512.00Excluding GST 10%
Available on backorder
Related products
Close
Fluke TL910 Electronic Test Probes
Product Features:
- 1 mm tips access hard to reach test points
- Probe tip length up to 100 mm
- Test lead length: 1 m
- 3 sets of spring loaded gold tips
- 2 sets of stainless steel tips
- Safety rating(s): CAT II 1000V, 3A
Close
Fluke TL26A Test Lead Set
Product Features:
- U-shaped nose for blade-shaped terminals
- Notched jaw for gripping screw heads, bare wire or terminals
- Serrated teeth for gripping threaded or wire-wrapped terminals
- Cluster of sharp needles for piercing small gauge wires (#22-#28 AWG)
- Large piercing needle for penetrating larger gauge wires
Close
Fluke AC283 Pincer Clips
Features
- 1A rating
- Use for continuity testing on circuit board components
- 4.49in (11.4cm) flexible insulated shaft
- CAT IV 600V, CAT III 1000V safety rated
- UL listed
- 1-year warranty
Close
Fluke TL224 Test Leads
Product Features:
- Rubber overmolded surfaces and finger-hugging curves for comfortable, reliable grip
- Safety shrouded, standard diameter banana plugs
- Right angle connector on one end and straight connector on other end
- Reinforced strain relief
- 1.5 meter silicone-insulated wire resists heat and cold
- Safety rating(s): CAT IV 600V, CAT III 1000V, 10A
- UL listed
Close
Fluke TL175 TwistGuard Test Leads
Features
- Extra-heavy duty strain relief on probe and plug
- Tested beyond 30,000 bends without failure
- -4 to 131°F (-20 to 55°C) operating temp
- Altitude of 6562ft (2000m)
- CAT II 1000V, CAT III 1000V, CAT IV 600V rated
- 10A max, Pollution Degree 2
- Conforms to EN61010-031
- 1-year warranty
Close
Fluke TL71 Test Lead Set
Fluke TL71 Offers
Test leads are an integral part of the complete measurement system and extend the capabilities of your digital multimeter. The TL71 premium test lead set has one pair of red and black comfort grip probes with flexible silicone-insulated, right-angle test leads. With distinctive comfort grip probes, they are heat and cold resistant with safety ratings up to CAT III 1000 V.
Features
- One pair (red, black) comfort grip probes with silicone insulated, right-angle test leads
- Recommended for µV measurements
- CAT II 1000 V, 10 A rating
- CAT III 1000 V, CAT IV 600V only with protective cap
- One year warranty
Applications
- Test and measurement
- Oil and gas
- R&D
- Electronics design
- Electronics service
- Repair and maintenance
- Electrical
- Industrial
Close
Fluke TL76 Test Lead Set
Features
- Removable, insulated IC caps allow probing on closely spaced leads and compliance with GS38
- CAT II 1000 V, 10 A rating
- CAT III 1000 V, CAT IV 600V only with protective cap
Close
Fluke TL930 Patch Cords
Fluke TL930 Offers
- 1 pair (red, black) multi-stacking 4 mm banana plug patch cords
- Nickel-plated banana plugs
- 61 cm long PVC insulated leads
- 30 V rms or 60 V DC, 15 A
- One year warranty
