The Fluke TP82 Insulating Piercing Clips, 2mm (Red and Black) are made of stainless steel and pierce insulation on 14, 16 and 18 gauge wire. You can control needle depth to minimize insulation damage. These clips are essential for use under the hood or under the dash. Use them on fuel injectors or sensors while providing complete insulation to grounding, due to design. The Fluke TP81 also connects to banana jack leads.
Previous product
Back to products
Fluke TP81 Insulation Piercing Clip Set
$132.00
Excluding GST 10%
Next product
Fluke TP88 Rigid Back Probe Pins
$42.00
Excluding GST 10%
Fluke TP82 Insulation Piercing Clip Set
$132.00Excluding GST 10%
- Banana jack accepts all DMM and banana jack leads
- Non-rotating banana jack prevents leads from tangling, allowing you to tighten/loosen clamp while still connected to the test lead
- For use with test leads with 2 mm probes
- Tested to 60 V DC
Available on backorder
Related products
Close
Fluke BT-520 Battery Analyzer
Key features
Fluke BT510 key features:
- Battery Voltage – During the internal resistance test, Fluke Battery Analyzers also measure the voltage of the battery under test
- Discharge Volts – The Discharge mode collects the voltage of each battery multiple times at a user defined interval during a discharge or load test. Users can calculate the time a battery takes to drop to the cut-off voltage and use this time to determine the capacity loss of the battery
- Ripple Voltage Test – Measures unwanted residual ac component of the rectified voltage in dc charging and inverter circuits. Allows users to test ac components in dc charging circuits and find one of the root causes of battery deterioration
- Meter and Sequence Modes – The Meter mode is used for a quick test or troubleshooting. In this mode you can save and read the readings in a measurement or time sequence. The Sequence mode is for maintenance tasks with multiple power systems and battery strings. Before a task starts, users can configure a profile for the task for data management and report generation
- Threshold and Warning – Users can configure a maximum of 10 sets of thresholds and receive a Pass/ Warning/ Fail indication after each measurement
- Intercell Strap Resistance Test and Data Management – Measures the resistance of the intercell connection between batteries in a string. Once the measurements are completed Fluke Battery Management Software version 1.0.69 can now report the strap resistance for a battery string or historical data over time.
- AutoHold – When AutoHold is turned on, a reading is captured when it remains stable for 1 second. The reading is then released when a new measurement starts
- AutoSave – When AutoSave is turned on, measured values are saved to internal memory automatically after an AutoHold reading is captured
Close
Fluke 190 Series II 60MHz ScopeMeter Oscilloscope
Features
- Four independent isolated input channels
- 60, 100, 200 and 500 MHz bandwidths
- Sample rate: Up to 2.5 GS/s
- Sample rate resolution: Up to 400 ps
- Deep memory: 10,000 point per trace waveform capture
- CAT III 1000 V / CAT IV 600 V safety rating
- Seven hour, high performance Li-ion batteries
- Battery door for convenient battery access
- Isolated USB ports for memory devices and PC connectivity
Close
Fluke 424D Laser Distance Meter
Professional-grade, automated endpiece correction, 80m/260ft range
Features
- Reduction of estimation errors
- Range: 80m/260ft
- Max range: 100m (330ft)
- Inclination sensor for taking measurements in hard to reach areas
- Compass provides a “heading” for distance measurement
- Automated endpiece correction
- Advanced laser technology for distance measurement
- Instant measurement with one-button operation
- Quick calculation of area (square footage) and volume
- Minimum/maximum function
- Improved battery life from automatic shut-off feature
- Enhanced Pythagoras calculation
- Tripod mode
- Stake out function
- Audible keypad feedback
- Storage of the last twenty measurements for quick recall of distance
- IP54 protection
Close
Fluke 123B Industrial ScopeMeter® Hand-Held Oscilloscope, 20 MHz
Features
- Dual-input digital oscilloscope and multimeter
- 20 MHz oscilloscope bandwidth
- Two 5000-count True RMS digital multimeters
- Connect-and-View™ trigger simplicity for hands-off operation
- IntellaSet™ technology automatically and intelligently adjusts numerical readout based on the measured signal
- Dual-input waveform and meter reading recorder for trending data over extended periods
- Recorder Event Detect captures elusive intermittent signals on repetitive waveforms up to 4 kHz
- Shielded test leads for oscilloscope, resistance and continuity measurements
- Resistance, continuity, diode and capacitance meter measurements
- Power measurements (W, VA, VAR, PF, DPF, Hz)
- Voltage, current and power harmonics
- Check Industrial networks with BusHealth physical layer tests against defined reference levels
- Save or recall data and instrument setups
- Store instrument setups defined by a test sequence for routine maintenance or most often used test procedures
- External optically isolated USB interface to transfer, archive and analyze scope or meter data
- Optional WiFi adapter connected to internal USB port to wirelessly transfer information to the PC, laptop or Fluke Connect® mobile app
- FlukeView® ScopeMeter® Software for Windows®
- Rugged design to withstand 3g Vibration, 30g shock, and rated IP51 according to EN/IEC60529
- Highest safety rating in the industry: safety rated for CAT IV 600 V
Close
Fluke TL175 TwistGuard Test Leads
Features
- Extra-heavy duty strain relief on probe and plug
- Tested beyond 30,000 bends without failure
- -4 to 131°F (-20 to 55°C) operating temp
- Altitude of 6562ft (2000m)
- CAT II 1000V, CAT III 1000V, CAT IV 600V rated
- 10A max, Pollution Degree 2
- Conforms to EN61010-031
- 1-year warranty
Close
Fluke 1738/EUS Three-Phase Power Loggers
Key features
- Three-phase advanced Fluke Connect compatible-power logger for making critical power quality and energy decisions in real-time
- Automatically captures and logs voltage, current, power, harmonics and associated power quality values.
- Provides the highest safety rating in the industry: 600 V CAT IV/1000 V CAT III rated for use at the service entrance and downstream
- Automatically logs all measured values and stores more than 20 separate logging sessions
Close
Fluke 830 Laser Alignment Tool
Features
- Intuitive guided user interface
- Intel XScale PXA270 running at 312MHz
- Ambient light protection
- 64MB RAM, 64MB flash memory
- 32 to 131°F (0 to 55°C) operating temp
- Compass measurement mode
- Dynamic machine tolerance check
- IP67 (submersible, dustproof) protection
Close
Fluke 6200-2 Portable Appliance Testers
Key features
Fluke Simplifies Portable Appliance Testing
- Dedicated key for each test for ‘one-touch’ testing
- Pre-set pass/fail levels to save time
- Large backlit display for easy reading
- Single mains socket for appliance connection
- Separate IEC socket for easy mains/extension lead testing
- Detachable test leads for quick field replacement
- Integral carrying handle
- USB port for data transfer
