Fluke Networks P4480004 TS52/44/42 Replacement Line Cord with 346A Plug, Compatible with 52 and 40 Series Test Sets
- Braided cables for durability and insulating boots over clips for safety
- Field replaceable
P4480004 – Fluke Networks TS52/44/42 Replacement Line Cord with 346A Plug
$198.00Excluding GST 10%
- TS52/44/42 replacement cord with 346A plug
- Braided cables for durability and insulating boots over clips for safety
- Field replaceable
- Compatible with TS52 and TS40 Series Test Sets
Available on backorder
Related products
Close
Fluke Amprobe TM-SWA CABLE AND SOFTWARE FOR TMD90 AND TMA10
Amprobe TM-SWA Cable and Software for TMD90A and TMA10A
Close
Fluke Amprobe UAT-620 UNDERGROUND UTILITY LOCATOR KIT W/CLAMP
Product Features:
- Multiple tracing modes allow you to locate and trace energized and de-energized utilities in several applications
- Intuitive Transmitter automatically chooses correct locating function based on connected accessory and includes selectable 8/33 kHz frequencies
- Receiver’s high-contrast display allows for clear viewing in full sunlight and features automatic backlight for shaded and dark areas
- Rated CAT IV 600 V, ensuring safety when working with energized cables
- Semi-automatic gain control quickly detects tracing signal and allows precise adjustment of receiver sensitivity
- Accurate depth measurement to 20 ft
- Rugged, durable construction
- Water and dust resistant to IP54
- Drop proof to 3.28 ft (1 m)
- Signal Clamp induces signal without making electrical contact
- Ground fault locating with optional A-Frame accessory (AF-600)
- Comes as complete kit, ready for use
- Three testing modes:
- Passive power mode (50/60 Hz) – Tracing energized lines conducting current (no Transmitter necessary)
- Passive radio mode (RF) – Using surrounding radio waves to trace underground utilities (no Transmitter necessary)
- Active mode – Using UAT-600-T Transmitter
- Three active modes with UAT-600-T Transmitter:
- Induction – Transmitter will automatically start to radiate signal around it with internal antenna, used for tracing individual cables where there is no access to line to connect test leads or clamp
- Direct connection with test leads – Most reliable method to trace individual cable or pipe
- Clamp – Provides efficient and safe method of applying locate signal to cable, where it is not possible or safe to gain access to cable for making electrical contact
- Main applications:
- Locate energized 50/60 Hz cables carrying current
- Identify location of all metallic utilities, pipes* or cables (energized or de-energized)
- Trace individual pipes* or cables (energized or de-energized)
- *Tracing of non-metallic pipes and conduits is possible after inserting metal fish tape or cable
- Special applications:
- Two frequency options: 8 kHz and 33 kHz
- Locate non-metallic pipes and sewer lines
- Take depth and current measurements
- Measure voltage, resistance and output current
- Advanced locating with two people
- Locate ground faults with the AF-600 A-Frame accessory
Applications
- Commercial and Residential Construction Contractors
- Water, Gas and Electric Installation and Repair Crews
- Pipe Laying Contractors
- Cable TV and Telecommunication Companies
- Electricians and General Contractors
Close
Fluke INDC8 – Insulated Heavy Duty Diagonal Cutter
Product Features:
- Nominal length: 8 in., 200 mm
- Cuts hard materials including steel and piano wire
- Power joint and precision cutting edges
- German CMV steel
- Designed to block potentially hazardous voltages from reaching you
- Subjected to a 10,000 V dielectric strength test, protection protection works
- Certified to 1,000 V ac and 1,500 V dc by VDE, (independent third-party lab)
- Comply to international standards such as IEC 60900 and ASTM F1505
- Critical part of NFPA 70E, which requires personal protective equipment and insulated tools rated for electrical installation
- Critical protective component between you and unplanned incident
Close
Fluke Amprobe AT-8030 Advanced Wire Tracer Kit
Key features
- Work directly on an energized circuit without the need to take equipment offline, CAT IV 600 V rated
- Save time searching for wires hidden behind walls, ceilings and floors with the Smart Sensorâ„¢, which displays the location and orientation of energized wires
- Pinpoint wire location with the large color LCD Receiver screen
- Identify breakers and fuses, as well as the location of a break, open or short
- Non-Contact Voltage Detection utilizes passive tracing without the Transmitter to verify if a wire is energized
- Includes the CT-400 Signal Clamp accessory for inducing a tracing signal on the cable when there is no access to bare conductors
Close
Fluke MP1-3R/1B – Magnetic Voltage Probes
Fluke MP1-3R/1B Magnetic Voltage Probes, Three Red, One Black
Close
Fluke 720A Kelvin-Varley Divider
- 0.1 ppm resolution, seven decades
- 0.1 ppm of input absolute linearity
- Built-in self calibration bridge
- Front panel self-calibration
Close
Fluke 720A Kelvin-Varley Divider (Copy)
- 0.1 ppm resolution, seven decades
- 0.1 ppm of input absolute linearity
- Built-in self calibration bridge
- Front panel self-calibration
Close
Fluke EI-162AC Clip on Current Transformer
Fluke Clip-On Current Transformer Features
- Performs selective and stakeless testing
- Inner diameter: 2 in.
- For use with Models 1623 and 1625
