For use with Fluke 174X Power Quality Analyzers.
Previous product
Back to products
Fluke 1773 Power Quality Analyzer
$11,308.00
Excluding GST 10%
Next product
Fluke-754/750SW Documenting Process Calibrator and Software Bundle Package
$14,564.00
Excluding GST 10%
Fluke-MA-C8 Line Power Cord to 4MM Sockets
$54.00Excluding GST 10%
Fluke MA C8 Wall Outlet Adapter
Available on backorder
Related products
Close
Fluke PRV240 Proving Unit, 240V
Fluke PRV240 Offers
Reduces the risk of shock and arc flash by removing unnecessary exposure to a potentially hazardous electrical environment while verifying the functionality of test tools before and after absence or presence of voltage is checked.
Features
- Sources both AC and DC steady-state voltage – supplies 240 V DC/AC
- A single LED indicates functionality, making this unit a simple-to-use solution for verification of your test tool
- Compatible with both high impedance or low impedance multimeters, clamp meters or two pole testers
- Voltage is sourced through recessed contacts that are activated when tested probes are inserted to avoid accidental contact
- Long battery life – 5,000 tests per set of four AA batteries
Test Before Touch
Provides a safe method to verify that your electrical test tool is operating properly before you conduct further tests. The concept of “Test Before Touch” (TBT) or three point test method involves testing your meter against a known live source before and after the actual measurement. This sequence verifies that your test tool is operating properly during the actual measurement.
Designed for safety and compliance
Safe and easy method for verifying proper operation of your test tool before attempting to test for either an energized source or a de-energized source without the need for cumbersome PPE, or in cases where no known voltage source is available. Your environment may still require minimal PPE such as hard, safety glasses or earplugs when using a proving unit.
Close
Fluke 720A Kelvin-Varley Divider
- 0.1 ppm resolution, seven decades
- 0.1 ppm of input absolute linearity
- Built-in self calibration bridge
- Front panel self-calibration
Close
Fluke CXT280
Product Features:
- Unbreakable
- Watertight
- Airtight
- Dustproof
- Chemical resistant
- Corrosion proof
- Buoyancy allows case to float in salt water with 7.94 lb load
- Automatic purge valve for quick equalization after changes in atmospheric pressure
- Features 0.25 in neoprene O-ring and ABS latches for excellent seal
- For use with many Fluke instruments
- For use with Fluke Multimeters and Earth Ground Testers
Close
Fluke VisiFault Visual Fault Locator
- Locates visual faults including tight bends, breaks and bad connectors
- Accelerates end-to-end fiber checks
- Easily verifies polarity and identifies fibers
- Features continuous and flashing modes
- Ergonomic case survives drops, impacts and vibrations
Close
Fluke INDC8 – Insulated Heavy Duty Diagonal Cutter
Product Features:
- Nominal length: 8 in., 200 mm
- Cuts hard materials including steel and piano wire
- Power joint and precision cutting edges
- German CMV steel
- Designed to block potentially hazardous voltages from reaching you
- Subjected to a 10,000 V dielectric strength test, protection protection works
- Certified to 1,000 V ac and 1,500 V dc by VDE, (independent third-party lab)
- Comply to international standards such as IEC 60900 and ASTM F1505
- Critical part of NFPA 70E, which requires personal protective equipment and insulated tools rated for electrical installation
- Critical protective component between you and unplanned incident
Close
Fluke Amprobe ULD-420 ULTRASONIC LEAK DETECTOR WITH TRANSMITTER
Product Features:
- 20 kHz to 90 kHz frequency range: optimal range for detecting a variety of leakage events
- Adjustable Transmitter signal strength for accurate leak pinpointing
- 3 filters to remove main noise frequencies in noisy environments
- 2.5″ LCD display with bargraph
- Adjustable Receiver Sensitivity
- Industrial headphones to help identify the source of the leak
- Parabola accessory directs the ultrasound towards the sensor
- Detachable Tubular Extension provides additional reach in hard to reach areas
Close
Fluke Amprobe ULD-400-T ULTRASONIC TRANSMITTER
Amprobe ULD-400-T Offers
Features
- Speaker
- Three LEDs: high/medium/low signals
- Low battery indicator
- Signal level “+/-” button
- On/Off button
Applications
- Fluid or gas tanks
- Building windows, doors or roofs
- Car windows and windshields
- HVAC/R vents
- Refrigerant pipelines
M1120 NST Neutral Supply Tester Kit
LCD screen to display measurement results and messages.
CAT IV 600V instrument and lead set compliance.
IP54 moisture and dust ingress rating.
Compact hand held unit housed in a lightweight heavy-duty case
Uniquely self powered passive device.
Power is taken directly from the user’s connections.
3 LED indicators and an LCD screen for status and measurement information.
An audible alarm is fitted internally as a secondary indicator. To indicate a pass at the end of the measurement cycle or a measurement failure.
