- ADP-SC/APC SC-APC Simplex Adapter
Previous product
Back to products
Fluke Networks ADP-SC/APC SC-APC Simplex Adapter
$57.00
Excluding GST 10%
Next product
Fluke Networks QuickClean-1.25-5P Quick Clean Cleaner 1.25 mm Fiber, LC and MU, 5 Pack
$1,204.00
Excluding GST 10%
Fluke Networks ADP-SC/APC SC-APC Simplex Adapter
$57.00Excluding GST 10%
- ADP-SC/APC SC-APC Simplex Adapter
Available on backorder
Related products
Close
Fluke Amprobe USB-KIT3 Download Module for Amprobe Precision Multimeters
Product Features:
- PC Interface Kit
- Download software with connection cable
- For Amprobe Multimeters
Close
Fluke VisiFault Visual Fault Locator
- Locates visual faults including tight bends, breaks and bad connectors
- Accelerates end-to-end fiber checks
- Easily verifies polarity and identifies fibers
- Features continuous and flashing modes
- Ergonomic case survives drops, impacts and vibrations
Close
Fluke TP912 Replacement Probe Tips for Model TL910
Fluke TP912 Offers
- Five sets of gold plated and stainless steel tips
- One year warranty
Close
Fluke INDC8 – Insulated Heavy Duty Diagonal Cutter
Product Features:
- Nominal length: 8 in., 200 mm
- Cuts hard materials including steel and piano wire
- Power joint and precision cutting edges
- German CMV steel
- Designed to block potentially hazardous voltages from reaching you
- Subjected to a 10,000 V dielectric strength test, protection protection works
- Certified to 1,000 V ac and 1,500 V dc by VDE, (independent third-party lab)
- Comply to international standards such as IEC 60900 and ASTM F1505
- Critical part of NFPA 70E, which requires personal protective equipment and insulated tools rated for electrical installation
- Critical protective component between you and unplanned incident
Close
Fluke CXT280
Product Features:
- Unbreakable
- Watertight
- Airtight
- Dustproof
- Chemical resistant
- Corrosion proof
- Buoyancy allows case to float in salt water with 7.94 lb load
- Automatic purge valve for quick equalization after changes in atmospheric pressure
- Features 0.25 in neoprene O-ring and ABS latches for excellent seal
- For use with many Fluke instruments
- For use with Fluke Multimeters and Earth Ground Testers
Close
Fluke Amprobe ACD-14-PRO Dual Display 600 A TRMS Clamp Multimeter
Product Features:
- Large LCD with dual display can show voltage and amps simultaneously
- True-RMS for accurate voltage measurements in noisy environments
- Low pass filter for current and voltage measurements on variable frequency drives
- Amp-Tip function for precise low current measurement down to 0.1 amp
- Ideal for HVAC applications with temperature, DC micro-amps and capacitance measurements
- Performs non-contact voltage detection (NCV)
- In-rush current measurement
- Audible continuity and diode test
- Data hold function
- Auto ranging instantly selects correct range
- Auto power off and low battery indicator
- Safety rated to CAT III 600 V
Close
Fluke LVD1A Volt Light
- Built-in flashlight
- Detector glows blue when AC voltage is present
- Detector glows red when it is at the source
Close
Fluke PRV240 Proving Unit, 240V
Fluke PRV240 Offers
Reduces the risk of shock and arc flash by removing unnecessary exposure to a potentially hazardous electrical environment while verifying the functionality of test tools before and after absence or presence of voltage is checked.
Features
- Sources both AC and DC steady-state voltage – supplies 240 V DC/AC
- A single LED indicates functionality, making this unit a simple-to-use solution for verification of your test tool
- Compatible with both high impedance or low impedance multimeters, clamp meters or two pole testers
- Voltage is sourced through recessed contacts that are activated when tested probes are inserted to avoid accidental contact
- Long battery life – 5,000 tests per set of four AA batteries
Test Before Touch
Provides a safe method to verify that your electrical test tool is operating properly before you conduct further tests. The concept of “Test Before Touch” (TBT) or three point test method involves testing your meter against a known live source before and after the actual measurement. This sequence verifies that your test tool is operating properly during the actual measurement.
Designed for safety and compliance
Safe and easy method for verifying proper operation of your test tool before attempting to test for either an energized source or a de-energized source without the need for cumbersome PPE, or in cases where no known voltage source is available. Your environment may still require minimal PPE such as hard, safety glasses or earplugs when using a proving unit.
