In today’s fast-paced workplace maximizing productivity is essential. Whether installing new fiber links or troubleshooting an existing network, the faster you can locate a problem, the faster you can fix it. That’s easier said than done when you are faced with a complex network of fibers, connectors and patch cords.
Fluke VisiFault Visual Fault Locator
$699.00Excluding GST 10%
- Locates visual faults including tight bends, breaks and bad connectors
- Accelerates end-to-end fiber checks
- Easily verifies polarity and identifies fibers
- Features continuous and flashing modes
- Ergonomic case survives drops, impacts and vibrations
Available on backorder
Related products
Close
Fluke 720A Kelvin-Varley Divider
- 0.1 ppm resolution, seven decades
- 0.1 ppm of input absolute linearity
- Built-in self calibration bridge
- Front panel self-calibration
Close
Fluke EI-162AC Clip on Current Transformer
Fluke Clip-On Current Transformer Features
- Performs selective and stakeless testing
- Inner diameter: 2 in.
- For use with Models 1623 and 1625
Close
Fluke Amprobe ULD-420 ULTRASONIC LEAK DETECTOR WITH TRANSMITTER
Product Features:
- 20 kHz to 90 kHz frequency range: optimal range for detecting a variety of leakage events
- Adjustable Transmitter signal strength for accurate leak pinpointing
- 3 filters to remove main noise frequencies in noisy environments
- 2.5″ LCD display with bargraph
- Adjustable Receiver Sensitivity
- Industrial headphones to help identify the source of the leak
- Parabola accessory directs the ultrasound towards the sensor
- Detachable Tubular Extension provides additional reach in hard to reach areas
Close
Fluke Amprobe AT-6030 Advanced Wire Tracer Kit
Key features
- Work directly on an energized circuit without the need to take equipment offline
- Save time searching for energized and de-energized wires hidden behind walls, ceilings and floors
- Pinpoint wire location with the large color LCD Receiver screen featuring four unique modes
- Identify breakers and fuses, as well as the location of a break, open or short
- Non-Contact Voltage Detection utilizes passive tracing without the Transmitter to verify if a wire is energized
- Includes the CT-400 Signal Clamp accessory for inducing a tracing signal on the cable when there is no access to bare conductors
Close
Fluke INDC8 – Insulated Heavy Duty Diagonal Cutter
Product Features:
- Nominal length: 8 in., 200 mm
- Cuts hard materials including steel and piano wire
- Power joint and precision cutting edges
- German CMV steel
- Designed to block potentially hazardous voltages from reaching you
- Subjected to a 10,000 V dielectric strength test, protection protection works
- Certified to 1,000 V ac and 1,500 V dc by VDE, (independent third-party lab)
- Comply to international standards such as IEC 60900 and ASTM F1505
- Critical part of NFPA 70E, which requires personal protective equipment and insulated tools rated for electrical installation
- Critical protective component between you and unplanned incident
Close
Fluke CXT280
Product Features:
- Unbreakable
- Watertight
- Airtight
- Dustproof
- Chemical resistant
- Corrosion proof
- Buoyancy allows case to float in salt water with 7.94 lb load
- Automatic purge valve for quick equalization after changes in atmospheric pressure
- Features 0.25 in neoprene O-ring and ABS latches for excellent seal
- For use with many Fluke instruments
- For use with Fluke Multimeters and Earth Ground Testers
Close
Fluke Amprobe ACD-14-PRO Dual Display 600 A TRMS Clamp Multimeter
Product Features:
- Large LCD with dual display can show voltage and amps simultaneously
- True-RMS for accurate voltage measurements in noisy environments
- Low pass filter for current and voltage measurements on variable frequency drives
- Amp-Tip function for precise low current measurement down to 0.1 amp
- Ideal for HVAC applications with temperature, DC micro-amps and capacitance measurements
- Performs non-contact voltage detection (NCV)
- In-rush current measurement
- Audible continuity and diode test
- Data hold function
- Auto ranging instantly selects correct range
- Auto power off and low battery indicator
- Safety rated to CAT III 600 V
Close
Fluke 752A Reference Divider
- 10:1 and 100:1 divider outputs
- Output uncertainty 0.2 ppm and 0.5 ppm
- Built-in calibration bridge
- Dynamic Resistor Matching™
- System switching for ease of use
- Operating modes
