In today’s fast-paced workplace maximizing productivity is essential. Whether installing new fiber links or troubleshooting an existing network, the faster you can locate a problem, the faster you can fix it. That’s easier said than done when you are faced with a complex network of fibers, connectors and patch cords.
Fluke VisiFault Visual Fault Locator
$699.00Excluding GST 10%
- Locates visual faults including tight bends, breaks and bad connectors
- Accelerates end-to-end fiber checks
- Easily verifies polarity and identifies fibers
- Features continuous and flashing modes
- Ergonomic case survives drops, impacts and vibrations
Available on backorder
Related products
Close
Fluke Amprobe TM-SWA CABLE AND SOFTWARE FOR TMD90 AND TMA10
Amprobe TM-SWA Cable and Software for TMD90A and TMA10A
Close
Fluke 720A Kelvin-Varley Divider
- 0.1 ppm resolution, seven decades
- 0.1 ppm of input absolute linearity
- Built-in self calibration bridge
- Front panel self-calibration
Close
Fluke Amprobe AT-8030 Advanced Wire Tracer Kit
Key features
- Work directly on an energized circuit without the need to take equipment offline, CAT IV 600 V rated
- Save time searching for wires hidden behind walls, ceilings and floors with the Smart Sensor™, which displays the location and orientation of energized wires
- Pinpoint wire location with the large color LCD Receiver screen
- Identify breakers and fuses, as well as the location of a break, open or short
- Non-Contact Voltage Detection utilizes passive tracing without the Transmitter to verify if a wire is energized
- Includes the CT-400 Signal Clamp accessory for inducing a tracing signal on the cable when there is no access to bare conductors
Close
Fluke CXT280
Product Features:
- Unbreakable
- Watertight
- Airtight
- Dustproof
- Chemical resistant
- Corrosion proof
- Buoyancy allows case to float in salt water with 7.94 lb load
- Automatic purge valve for quick equalization after changes in atmospheric pressure
- Features 0.25 in neoprene O-ring and ABS latches for excellent seal
- For use with many Fluke instruments
- For use with Fluke Multimeters and Earth Ground Testers
Close
Fluke Amprobe ULD-400-T ULTRASONIC TRANSMITTER
Amprobe ULD-400-T Offers
Features
- Speaker
- Three LEDs: high/medium/low signals
- Low battery indicator
- Signal level “+/-” button
- On/Off button
Applications
- Fluid or gas tanks
- Building windows, doors or roofs
- Car windows and windshields
- HVAC/R vents
- Refrigerant pipelines
Close
Fluke 752A Reference Divider
- 10:1 and 100:1 divider outputs
- Output uncertainty 0.2 ppm and 0.5 ppm
- Built-in calibration bridge
- Dynamic Resistor Matching™
- System switching for ease of use
- Operating modes
Close
Fluke Amprobe ACD-14-PRO Dual Display 600 A TRMS Clamp Multimeter
Product Features:
- Large LCD with dual display can show voltage and amps simultaneously
- True-RMS for accurate voltage measurements in noisy environments
- Low pass filter for current and voltage measurements on variable frequency drives
- Amp-Tip function for precise low current measurement down to 0.1 amp
- Ideal for HVAC applications with temperature, DC micro-amps and capacitance measurements
- Performs non-contact voltage detection (NCV)
- In-rush current measurement
- Audible continuity and diode test
- Data hold function
- Auto ranging instantly selects correct range
- Auto power off and low battery indicator
- Safety rated to CAT III 600 V
M1120 NST Neutral Supply Tester Kit
LCD screen to display measurement results and messages.
CAT IV 600V instrument and lead set compliance.
IP54 moisture and dust ingress rating.
Compact hand held unit housed in a lightweight heavy-duty case
Uniquely self powered passive device.
Power is taken directly from the user’s connections.
3 LED indicators and an LCD screen for status and measurement information.
An audible alarm is fitted internally as a secondary indicator. To indicate a pass at the end of the measurement cycle or a measurement failure.
