|
Close
Fluke PM9081 Dual Banana Plug (Male) to Female BNC Adapter
Fluke PM9081/001 Offers
Dual Banana Plug 4 mm male to female BNC Adapter.
- Maximum Signal Voltage: 300V rms
- Maximum Voltage to Ground: 600V rms. CAT III per IEC 61010-031
Close
Fluke PM9082 Dual Banana Jack (female) to male BNC Adapter
Fluke PM9082/001 Offers
The set consists of two adapters. One red (signal) and one black (ground) 4-mm banana contact.
- Maximum Signal Voltage: 300V rms
- Maximum Voltage to Ground: 600V rms. CAT III per IEC 61010-031
Close
Fluke PM9091/001 50 Ohm Coaxial BNC cable set
Features
- Each set consists of three black cables with colored BNC male connectors (red, gray and black) for easy identification
- Cable length is 1.5 m
- Maximum Signal Voltage: 300 V rms
- Maximum Voltage to Ground: 600 V rms, CAT III per IEC 61010-031
- BB120 Shielded Banana to BNC Adapter is required to adapt to ScopeMeter 120 Series shielded banana jack inputs
Close
Fluke PM9092/001 50 Ohm Coaxial BNC cable set
Fluke PM9092/001 Offers
Each set consists of three black cables with colored BNC male connectors (red, gray and black) for easy identification
- Cable length is 0.5 m (1.6 ft).
- Maximum Signal Voltage: 300 V rms
- Maximum Voltage to Ground: 600 V rms. CAT III per IEC 61010-031
- Fluke BB120 Shielded Banana to BNC Adapter is required to adapt to ScopeMeter 120 Series shielded banana jack inputs.
Close
Fluke PM9093 Male BNC to Dual Female BNC Adapter
Features
- Male BNC to dual female BNC T-piece, set consists of two adapters
- Maximum Signal Voltage: 300 V rms
- Maximum Voltage to Ground: 600 V rms, CAT III per IEC 61010-031
Close
Fluke PM9096/201
Secondary pick-up for the 97AUTO, 1000:1.
Close
Fluke PPA9159-CAL Fine Increment Weight for kPa, mPa, bar or kgf/cm2 Weight Sets
What’s included with the Fluke PPA9159-CAL
- Fluke PPA9159-CAL Fine Increment Weight for kPa, mPa, bar or kgf/cm2 Weight Sets
Close
Fluke PPA9608-CAL Incremental Weights for psi Weight Sets
What’s included with the Fluke PPA9608-CAL
- Fluke PPA9608-CAL Incremental Weights for psi Weight Sets
Close
Fluke PPCH Automated Pressure Controller / Calibrator
- Hydraulic pressure controller to 200 MPa (30,000 psi)
- High precision control
- AutoRange feature
- For liquid pressures up to 30,000 psi (200 MPa)
- One or two Q-RPTs in each controller
- Supports external reference pressure transducers
- FLASH memory for simple and free embedded software upgrades via Fluke Calibration web-site
Close
Fluke PQ-MARKER Cable Marker Set
For use with the PQ400 Power Quality Window.
Close
Fluke PQ400 Power Quality Window with cables, cable ties & markers
Features
- Permanently connected voltage and current sensors located inside the electrical panel allow you to make power quality and energy measurements using the external access points without opening the panel door, reducing operator risk
- Voltage and current connections for three-phase voltages, neutral and ground cover most measurement scenarios
- Automatic probe detection for 1740 and 1730 series power quality and energy loggers and compatible clamps, eliminates the need to open cabinet to check the clamp model
- Full 360° rotation allows the window to be oriented in any direction
- Simple installation using a step drill bit and electro-hydraulic hole punch (114.3 mm, 4.5″ diameter)
- CAT IV, 600 V and CATIII 1000 V rating according to IEC61010-2-30
- Compatibility with standard 4 mm shrouded safety-socket voltage test leads makes it easier to make voltage connections, and increases safety by reducing the risk of accidentally touching live electrical components
