Fluke TL223 Test Lead Set
Features
- Designed to improve steadiness in slippery hands
- Rubber overmolded surfaces and finger-hugging curves
- 1-year warranty
Fluke TL224 Test Leads
Product Features:
- Rubber overmolded surfaces and finger-hugging curves for comfortable, reliable grip
- Safety shrouded, standard diameter banana plugs
- Right angle connector on one end and straight connector on other end
- Reinforced strain relief
- 1.5 meter silicone-insulated wire resists heat and cold
- Safety rating(s): CAT IV 600V, CAT III 1000V, 10A
- UL listed
Fluke TL225 Test Lead Kit
Features
- Low input impedance that eliminates stray voltages
- Indicate the real voltage on energized wires
- Non-energized circuits will read close to zero
- Works with meters with standard input spacing
- Rated CAT III 1000V & CAT IV 600V
What’s included with the Fluke TL225
- Stray Voltage Eliminator
- Silicone Test Lead Set
- Test Probe Set
- Carrying Case
Fluke TL238 SureGrip Test Lead Set
Features
Designed for high energy environments, this kit comes equipped with the TP238, TP280, and TL224.
- Up to 10A
- 1000V CAT III maximum
- 600V CAT IV (TP238 & TL224 only)
- Operating temperatures from -4 to 122°F (-20 to 50°C)
- IEC 1010-2-031
- Pollution degree 2
- 1-year warranty
Fluke TL26A Test Lead Set
Product Features:
- U-shaped nose for blade-shaped terminals
- Notched jaw for gripping screw heads, bare wire or terminals
- Serrated teeth for gripping threaded or wire-wrapped terminals
- Cluster of sharp needles for piercing small gauge wires (#22-#28 AWG)
- Large piercing needle for penetrating larger gauge wires
Fluke TL27 Test Leads
Product Features:
- Safety shrouded, standard diameter banana plugs
- Heavy duty EPDM insulation
- Length 1.5 m
- Safety rating(s): CAT III 1000V, 10A
- UL listed
Fluke TL28A Automotive Test Lead Set
Features
- Large jaws, long leads and a piercing needle inside the jaws
- Solid, spring-loaded copper clips with a wide 0.50″ (12.7 mm) jaw opening and serrated teeth
- Large piercing needle for penetrating larger gauge wires located inside the jaws
- 60″ (1.5 m), silicone-insulated leads, useable from -112 to 158°F (-80 to 70°C)
- Rated for 30 V, 10 A
-10%
Close
Fluke TL2X4W-PT7 2 x 4 Wire Ohms Test Lead, 1000V
Fluke TL2X4W-PT7 Offers
Features
- Two conductors per lead (one source and one measure)
- Perform 4 wire measurements with only two test leads
- 1000 volts maximum voltage between test lead and ground
- 1000 volts maximum transient over voltage and input voltage combined
-10%
Close
Fluke TL2X4W-TWZ
Fluke TL2X4W-TWZ Offers
2X4 WIRE OHMS SMD TEST TWEEZER
Fluke TL40 Retractable Tip Test Lead Set
Product Features:
- Sharp needle point lead tips
- Adjustable to 76 mm
- Extra hard probe tips provide long service life
- Flexible silicone insulated test leads
- Safety rating(s): CAT II 600V, 3A
Fluke TL71 Test Lead Set
Fluke TL71 Offers
Test leads are an integral part of the complete measurement system and extend the capabilities of your digital multimeter. The TL71 premium test lead set has one pair of red and black comfort grip probes with flexible silicone-insulated, right-angle test leads. With distinctive comfort grip probes, they are heat and cold resistant with safety ratings up to CAT III 1000 V.
Features
- One pair (red, black) comfort grip probes with silicone insulated, right-angle test leads
- Recommended for µV measurements
- CAT II 1000 V, 10 A rating
- CAT III 1000 V, CAT IV 600V only with protective cap
- One year warranty
Applications
- Test and measurement
- Oil and gas
- R&D
- Electronics design
- Electronics service
- Repair and maintenance
- Electrical
- Industrial
Fluke TL75 Hard Point Test Lead Set
Product Features:
- Comfort grip probes
- 48 in. PVC insulated test leads with right-angle shrouded banana plugs
- Recommended for general purpose measurements
- Safety rating(s): CAT II 1000V, 10A; CAT IV 600V, CAT III 1000V only with protective cap
- CSA listed