Close
Fluke PM9092/001 50 Ohm Coaxial BNC cable set
Fluke PM9092/001 Offers
Each set consists of three black cables with colored BNC male connectors (red, gray and black) for easy identification
- Cable length is 0.5 m (1.6 ft).
- Maximum Signal Voltage: 300 V rms
- Maximum Voltage to Ground: 600 V rms. CAT III per IEC 61010-031
- Fluke BB120 Shielded Banana to BNC Adapter is required to adapt to ScopeMeter 120 Series shielded banana jack inputs.
Close
Fluke PM9093 Male BNC to Dual Female BNC Adapter
Features
- Male BNC to dual female BNC T-piece, set consists of two adapters
- Maximum Signal Voltage: 300 V rms
- Maximum Voltage to Ground: 600 V rms, CAT III per IEC 61010-031
Close
Fluke PM9096/201
Secondary pick-up for the 97AUTO, 1000:1.
Close
Fluke PPA9159-CAL Fine Increment Weight for kPa, mPa, bar or kgf/cm2 Weight Sets
What’s included with the Fluke PPA9159-CAL
- Fluke PPA9159-CAL Fine Increment Weight for kPa, mPa, bar or kgf/cm2 Weight Sets
Close
Fluke PPA9608-CAL Incremental Weights for psi Weight Sets
What’s included with the Fluke PPA9608-CAL
- Fluke PPA9608-CAL Incremental Weights for psi Weight Sets
Close
Fluke PQ-MARKER Cable Marker Set
For use with the PQ400 Power Quality Window.
Close
Fluke PQ400 Power Quality Window with cables, cable ties & markers
Features
- Permanently connected voltage and current sensors located inside the electrical panel allow you to make power quality and energy measurements using the external access points without opening the panel door, reducing operator risk
- Voltage and current connections for three-phase voltages, neutral and ground cover most measurement scenarios
- Automatic probe detection for 1740 and 1730 series power quality and energy loggers and compatible clamps, eliminates the need to open cabinet to check the clamp model
- Full 360° rotation allows the window to be oriented in any direction
- Simple installation using a step drill bit and electro-hydraulic hole punch (114.3 mm, 4.5″ diameter)
- CAT IV, 600 V and CATIII 1000 V rating according to IEC61010-2-30
- Compatibility with standard 4 mm shrouded safety-socket voltage test leads makes it easier to make voltage connections, and increases safety by reducing the risk of accidentally touching live electrical components
Close
Fluke PressCal Pressure Calculation/Calibration Software
Fluke PRESSCAL Offers
Features
- Menu-driven, easy-to-use software
- Maintain multiple deadweight tester files
- Pressure-equivalent calculations with all corrections applied
- Pre-loaded calibration data
- 12 pressure units
- Windows 95 or higher running on a 486 PC (minimum)
Close
Fluke PRV240FS Proving Unit
Features
- Sources both ac and dc steady-state voltage – supplies 240 V dc/ac
- A single LED indicates functionality, making this unit a simple-to-use solution for verification of your test tool
- Compatible with both high impedance or low impedance multimeters, clamp meters or two pole testers
- Voltage is sourced through recessed contacts that are activated when tested probes are inserted to avoid accidental contact
- Long battery life – 5,000 tests per set of four AA batteries
Close
Fluke PTI120-9HZ Pocket Thermal Imager, 120 x 90, 9 Hz
Features
- With Fluke Connect® Asset Tagging you eliminate the tedium of sorting and organizing your infrared images
- By simply scanning your asset’s QR code or barcode, your infrared image and all of your date and time stamped information will be stored to your predefined folders
- Fully radiometric thermal imager gives you measurement data to the pixel with 120 x 90 infrared resolution (10,800 pixels)
- 3.5″ LCD touchscreen display offers IR-Fusion™ to blend a visible light image with an infrared image to more easily locate problems; simply slide your finger across the screen to adjust the setting
- Can withstand drop up to 1 meter
- IP54 enclosure rating
- -4 to 302°F (-20 to 150°C) temperature measurement range
- Pocket sized – small enough to carry every day without worry
- Stands up to dirt and water
- Quick scans of electrical equipment, machinery and other assets
Applications
- Electrical inspections
- HVAC/R inspections
- Mechanical
- Residential home inspections
- Light commercial maintenance
- Building diagnostics – building envelope and commercial/industrial facilities
Close
Fluke RPM80 Inductive Pick-Up/External Trigger
Product Features:
- Provides RPM readings
Close
Fluke RS400 Probe Accessory Replacement Kit for the VPS400 Series
Compatible with the FLuke VPS410B, VPS410G, VPS410R, and the VPS410V.
